Alcatel Omni Switch/Router User Manual Download | Manualshive

Page: 845 / 1100

background image

The WAN Port Software Menu

Page 28-19

TOS for Voice Signaling Data

Set the priority for voice signaling data streams. The value must be entered in hexadecimal
format translated from binary, and can use either IP Precedence or Differentiated Services
Code Point (DSCP). Enter

0

to disable this feature. See

Type of Service (ToS)

on page 28-2

above for a more detailed explanation of ToS.

TOS Mask for both TOS Value

Set the mask bits for both voice data and signaling data. Enter

0

to disable this feature.

Signaling IP Address

When a data frame cannot be identified by the ToS voice data or ToS signaling data, the
Signaling IP Address is checked. Matched frames are loaded on a High Priority Software
Queue and a Nominal Hardware Queue.

Signaling IP Mask

The mask associated with the Signaling IP Address described above.

KeepAlive Up Count

If the switch detects that a port may be down, it will generate echo message requests to the
far end of the connection. The KeepAlive Up Count is the number of requests sent from the
port when the port transitions from Down to Up, to verify the status of the port. The valid
range is 0-255.

KeepAlive Down Count

If the switch detects that a port may be down, it will generate echo message requests to the
far end of the connection. The KeepAlive Down Count is the number of requests sent from
the port when the port transitions from Up to Down, to verify the status of the port. This only
displays if the port is using PPP as its encapsulation type. The valid range is 0-255.

KeepAlive Timeout

The number of 100 millisecond increments between generated echo message requests. This
only displays if the port is using PPP as its encapsulation type. The valid range is 0-255.

DTR Pulse Width

A Data Terminal Ready (DTR) Pulse is sent at the hardware level to determine a port is still
synchronized with its far end connection. The Pulse Width is the number of 100 millisecond
increments that the pulse lasts. This only displays if the port is using PPP as its encapsulation
type. The valid range is 0-255.

DTR Pulse Count

A Data Terminal Ready (DTR) Pulse is sent at the hardware level to determine a port is still
synchronized with its far end connection. The Pulse Count is the number of pulses generated
when a line is down. This only displays if the port is using PPP as its encapsulation type. The
valid range is 0-255.

«
...
843
844
845
846
847
...
»

Summary of Contents for Omni Switch/Router













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Omni Switch/Router

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: Abocom Pages: 1

Brand: G-Technology Pages: 35

Firebox SOHO 6 Wireless

Brand: Watchguard Pages: 8

Brand: Dahua Pages: 24

Brand: Opengear Pages: 2

Brand: Oracle Pages: 112

Brand: BSD Networks Pages: 7

Brand: CyberTAN Pages: 67

Brand: Accton Technology Pages: 78

Brand: Maipu Pages: 26

Brand: US Robotics Pages: 180

Brand: Variscite Pages: 17

Brand: LaView Pages: 2

Dynalink MyZone 3G24W

Brand: NetComm Pages: 5

Network Adapter AC AAP

Brand: Extron electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands