background image

Open Problem Reports and Feature Exceptions

page 78

OmniSwitch 6800/6850/9000—Release 6.1.3.R01

PR 107086

User with readwrite-scp-sftp privileges is initially queried for authentication and authorization on an 
OS6850. After login to the scp/sftp shell, only accounting requests are sent to  server (if 
enabled), commands are not queried for authorization.

Workaround: 

There is no known workaround at this time.

PR 107278

SNMP variable policyStatsQueryCount always show as zero.

Workaround: 

See policyStatsAccessCount instead.

PR 107543

If Loopback0 is defined by the user and there is not a physical route for that IP subnet, a RADIUS client 
will not be able to communicate with a RADIUS server. As a result, RADIUS authentication will fail as 
the server is unreachable.

Workaround: 

There is no known workaround at this time.

General

Problem Reports

PR 86853

A stack of 9 or greater is not supported on an OS6800 or OS6850.

Workaround: 

The maximum stack elements is 8.

PR 93114

If an ingress packet is oversized, it is not for broadcast or multicast anymore. As a result, ingressing over-
sized layer 2 multicast packets are counted as unicast packets.

Workaround: 

There is no known workaround at this time.

PR 97213

On an OS9000, in all CPU exceptions, a Trace Buffer dump is offered at the beginning of the exception.

Workaround: 

There is no known workaround at this time.

System

Summary of Contents for OmniSwitch 6800























































































Reviews: