background image

5

DEMOLITION BREAKER

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period 

of 60 months from the date of purchase. Defects that occur within this warranty period, 

under normal use and care, will be repaired, replaced or refunded at our discretion. 

The benefits conferred by this warranty are in addition to all rights and remedies in respect of 

the product that the consumer has under the Competition and Consumer Act 2010 and similar 

state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer 

Law. You are entitled to a replacement or refund for a major failure and for compensation 

for any other reasonably foreseeable loss or damage. You are also entitled to have the goods 

repaired or replaced if the goods fail to be of acceptable quality and the failure 

does not amount to a major failure.

AFTER SALES SUPPORT

 

 

1300 855 831

 

support@scheppach.com.au

AUS Hotline Costs

MODEL: AB1900 PRODUCT CODE: 61755 08/2018

5

REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

Summary of Contents for 61755



















Reviews: