background image

25

Digital Inverter Generator with Pure Sine Wave

AFTER SALES SUPPORT

e-mail:  info.aldi@positecgroup.com

1300 889 028

MODEL: №. XG-KF2000  •  03/2020  •  700069

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail:  info.aldi@positecgroup.com

1300 889 028

Digital Inverter Generator with Pure Sine Wave

MODEL: №. XG-KF2000  •  03/2020  •  700069

2.  Allow the engine to slow down and idle for approximately 15-30 seconds. 

Remove any appliances connected to either of the 2 AC sockets.

3.  Press the engine On/Off switch (2) to the “OFF” position as indicated by an 

“O” (Fig. U). The unit will stop running and is shut down.

        Now follow the normal starting procedure to restart the generator.

Emergency Stop, and / or failure of On/off Switches (NOT 

RECOMMENDED EXCEPT IN EMERGENCY)

In the case of an emergency that requires the 

generator to be shut down as fast as possible:
1.  Turn “OFF” the 240Va.c Outlet Power On/Off 

switch (1). If the switches have failed and power is 

still going to the appliance outlets quickly move 

to step 2.

2.  Press the engine On/Off switch (2) to the “OFF” 

position as indicated by an “O” (Fig. U). The unit 

should stop running. If the switches have not shut 

down the generator, you can quickly remove / pull out the plugs of the 

appliances plugged into the AC sockets (9) that need to be shut down.

3.  Where the engine keeps operating, don’t panic, turn the fuel lever / tap 

(23) 

clockwise 

to the “OFF” position (Fig. T). The generator will run out of 

fuel within one minute and then stop.

Do not use the generator again until the generator is serviced by an 

authorised service agent and the product is repaired, checked and the fault 

corrected.

As always in an emergency protect people that could be in harms way first.

Carbon build up

Carbon build up can be a problem on generators as the loading on the engine 

can vary considerably. Running the generator at low loading for extended 

periods can cause carbon build up.
Carbon build up in the engine can be reduced by operating the generator 

at approximately 75% of rated load for 25% of the time the generator is 

used. i.e, if the generator is used for 4 hours on low load i.e 800W or less, run 

the generator for 1 hour at around 75% of rating. This is only required if the 

generator has been used for less than 25% of rated load for extended periods. 

i.e 2 hrs or more.

NOTE:

 For best operation and long engine life use unleaded fuel without 

ethanol.

U.

Summary of Contents for 700069









































Reviews: