ALDI 811322, User Manual

12

13

Use

Troubleshooting

when using the product.

(Fig. K)

To switch on, press the on/off button   

9

 below the display 

10

.

-  The display 

10

 lights up.

-  The last applied pressure indication, 

PSI, BAR or KG/CM² is displayed.

To switch off, press the on/off button   

9

 for approx. 3 seconds.

NOTE!

If the product is not operated for more 

than 90 seconds, it switches off automat-

ically.

Measuring tyre pressure

NOTE!

Applies only to Schrader valve 

X

:

1.  First, remove the dust cap.

2.  Screw the valve adapter 

2a

 on the 

compressed air hose with threaded 

connection 

2

 to the Schrader valve 

X

, see

 Fig. F. 

2.  Switch on the product, see 

Fig. K.

3. The 

10

 display lights up and the last 

set pressure indicator 

15

 PSI, BAR or 

KG/CM² is displayed. 

4.  The pressure existing in the inflated 

item is shown in the corresponding 

pressure display.

Set pressure

(Fig. K)

1.  Turn on the product as described 

above.

2.  By briefly pressing the on/off button 

9

 you can set the desired pres-

sure to PSI, BAR or KG/CM².

  The pressure display 

15

 shows the 

value 0.00.

3.  By pressing the setting buttons 

16

or 

17

   you switch to the pressure 

specification.

-  The last set pressure is displayed and 

flashes.

3.  By pressing the setting buttons 

16

or 

17

   you can now set the pressure 

up to the max. pressure of 8.25 bar / 

120 PSI / 8.41 KG/CM².

-  If you press and hold down the setting 

buttons 

16

   or 

17

  , the setting will 

be accelerated. 

4.  When the desired pressure is set, wait 

about 2 seconds.

-  The display changes back to the pres-

sure indication. The pressure display 

15

 shows the value 0.00.

NOTE!

The set pressure is automatically convert-

ed into the other pressure values. For ex-

ample, if you set 2.5 BAR and then switch 

to PSI, the value is automatically convert-

ed to 36 PSI. 

Pumping process 

!

WARNING!

Risk of overheating

-   The air slots 

21

 on the underside of 

the product (Fig. M) must not be cov-

ered during the pumping process. 

There is a risk of overheating.

(Fig. L)

1.  When the product is off, turn the prod-

uct on as described above.

2.  Now press the on/off button

18

   on 

the top of the product.

  The built-in compressor starts and 

runs until the set pressure is reached.

NOTE!

During the pumping process the current 

pressure is displayed.

3.  After reaching the set pressure, the 

compressor stops pumping.

4.  Press the on/off pressure switch

18

on the top of the product to switch off 

the compressor.

NOTE!

-  You can only activate the compressor 

if the product has been switched on 

using the on/off button   

9

.

 -  You can switch off the compressor be-

fore it reaches the set pressure. To do 

this, press the on/off pressure switch 

18

  .

Note, that if you switch off the compres-

sor before reaching the set pressure, the 

inflated item, e.g. a bicycle tyre, may not 

meet the required specifications (tyre 

pressure).

5.  After the pumping process, unscrew 

the compressed air hose with thread-

ed connection 

2

 or any screwed-in 

adapters 

5

, 

6

 or 

7

from the valve.

6.  If present, screw the dust cap onto the 

valve.

NOTE!

Applies only to Presta valve 

Z

:

Close the valve and screw on the dust cap.

NOTE!

Air can escape from the valve when the 

compressed air hose with threaded con-

nection 

2

, or the previously described 

adapters 

5

, 

6

 or 

7

from the valve 

is disconnected. Be sure to remove the 

threaded air hose 

2

 or adapters 

5

6

7

 quickly.

Auxiliary light on/off 

NOTE!

The LED lamp of the auxiliary light 

is suitable for extreme tempera-

tures down to -21°C.

(Fig. L) 

To switch on the auxiliary light 

19

 press 

the light switch 

20

.

To switch off, press the light switch 

20

again. 

The auxiliary light 

19

 can be used inde-

pendently of the product.

TROUBLESHOOTING

No reaction when the product is 

switched on by pressing the on/off 

button   

9

-  The battery is not charged. Charge 

the battery.

No reaction when the compressor is 

switched on by pressing the on/off 

pressure switch 

18

-  The battery is not charged. Charge 

the battery.

-  The product is not switched on. Switch 

on the product by pressing the on/off 

button   

9

.

CLEANING AND CARE IN-

STRUCTIONS

!

CAUTION!

Risk of injury! 

Before cleaning, you must dis-

connect the charging plug. There 

is a risk of electric shock!

-  only clean with a dry cloth

-  do not use any strong detergents and/

or chemicals

-  do not immerse in water

-  store in a cool, dry place and protected