SERVICE INSTRUCTIONS
Rolla Reels
AP650/
AP840/
WP855
Description
With covers manufactured from high quality impact resistant and UV stabalised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the new series of Rolla Reels from Alemite Lubrequip will provide you with a reliable cost
effective means of storing and retrieving hose assemblies in your workshop or garden. The reels can be floor, ceiling or wall mounted
and the detachable mounting bracket facilitates ease of reel mounting and storage (if required). Each and every reel is tested for its
ability to hold pressure and hose retraction prior to leaving the factory and stringent adherence to assembly and operation standards
guarantees you years of trouble free operation. Non snag roller guide assemblies, crimped hose ends and dependable swivels and
spring assemblies are other product features that ensure trouble free hose storage and retrieval.
Specifications
Head Office NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
VIC
TEL: (03) 8787 8288
FAX: (03) 8787 8266
QLD
TEL: (07) 3889 8480
FAX: (07) 3889 8490
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
TAS
TEL: (03) 6343 0477
FAX: (03) 6343 0911
Visit our website at
www.alemite-lubrequip.com.au
Email - info@alemite-lubrequip.com.au
Operation
1
Check your Rolla Reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2
Latching mode switch, when your Rolla Reel is in free run state, pull out the
hose and allow it to retract after hearing the first, second or third click.
3
To unlatch the reel slowly pull out the hose until the clicking noise stops, and then let
the hose retract until the hose stop rests against the hose guide.
4
NOTE: To avoid damage to the Rolla Reel, always hold onto the hose while it is
rewinding. Periodically check the hose condition for wear or damage and check the
swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1
Make sure incoming line pressure does not exceed the rated operating pressure for
your model hose reel.
2
Use proper eye protection when assembling and using the hose reel.
3
Use soap and water when checking for leaks.
4
Keep children away from the work area.
Installation Of Reel
1
For overhead ceiling mounting: install reel at least 3 metres
above the floor.
2
You will need to purchase appropriate hardware for the mounting
of your new reel.
3
The reel base has three 10.5mm (13/32) drilled holes for mounting
on a suitable flat surface. Figure 2 is a template showing the
correct location of the 3 mounting holes in the base.
4
Using the three holes in the base, mount the reel in the desired
location. Be sure to use appropriate hardware and to tighten the
reel securely to the mounting location.
5
Apply Teflon tape or pipe sealant to the outlet fitting on the Rolla
Reel hose, then attach to desired tool or nozzle. Check connection
for any leakage, also check the Rolla Reel hose for correct
operation. See operation section. If hose stop adjustment is
required, pull hose from reel and allow the reel to latch at the
desired length. Loosen hose stop bolts and slide hose stop to a
position close to the hose guide. Tighten hose stop bolts and
unlatch the reel.
Uses
Air and Water
Hose Lengths
AP650 – 15m of 10mmID hose. AP840 – 13m of 12mmID hose. WP840 – 18m of 12mmID hose.
Materials
Plastic covers, steel spring & Buna “N” seals
Weight
11Kgs
Inlet
AP650 – 3/8”BSPT (m). AP840 – 1/2”BSPT(m). WP855 – 1/2”BSP(m)
Outlet
AP650 – 3/8”BSPT (m). AP840 – 1/2”BSPT(m). WP855 – 1/2”BSP(m)
