background image

DM PRO (D6) Trigger Test Procedure (2) 

Software: V2.00   Trigger V2.00
DD: 12/28/99
REV: D 

I) UPLOAD D6 USER & TRIGGER PROGRAM 

:

A)

Press the “

CURSOR

” button while powering up the D6 unit. 

B)

Press the “

STORE

” button. 

- Press “

CURSER

” button until you see “ 

Load USER from Factor

y

?    (STR)

- Press “

STORE

” again to LOAD USER PROGRAM. 

- Press“

CURSER

” button until you see “ 

Load TRIGS from Factory?   (STR)

- Press “

STORE

” again to LOAD TRIGGER PROGRAM. 

C)

Press “

MIDI

” button and adjust the 

VALUE ENCODER 

until display reads

AuxPed  Ctl#: 016

”.

Press

CURSER

¾

 1-time and adjust the 

VALUE ENCODER 

until display reads 

AuxPed  Ctl#: KIT+”.

D

)  Press “

KIT

” button. 

      Adjust “

VALUE

ENCODER

 until “

KIT

” button starts to flash. 

      Adjust “

VALUE

ENCODER

until display reads “

00   “ProRockKit

”.

      Press “

KIT

” Button to load drumkit.

E)

Plug

FOOT SWITCH

 into the 

AUX PEDAL

 plug.  Press 

KIT

button.  Press the 

FOOT SWITCH

, and the display should load the next kit.

*

FAIL UNIT IF DIFFERENT

*

E

)  TURN POWER OFF……… 

II.  TRIGGER TEST:

Equipment:

1. 1 pcs of ¼” Mono audio CABLE &  Special make Y CABLE. 
2. 1 pcs of headphone. 
3. 1 D6 Unit. 

4.

1 Trigger fixture (YAMAHA DRUM PAD)
1 Trigger pad w/clamp

5.

1 Drum stick

6.

1 foot switch 

NOTED: PLEASE MAKE SURE D6 UNIT HAS BEEN UPLOAD WITH USER 

PROGRAM BEFORE THIS TIRGGER TEST PROCEDURE. 

1

Summary of Contents for DM Pro Kit













































Reviews: