background image

A

lfaSpid Rotator 

www.alfaradio.ca 

Page 10 

Page 10 of 21 

A

lfa Radio Ltd. 11211 - 154 St. Edmonton, Alberta, Canada T5M 1X8  780 466 5779 

 

- Normal Operations Mode 

 

In Normal Operations Mode, the   and   buttons cause rotation 
as long as the buttons are pressed.  Pressing 

 while in normal 

operations mode will take you to setup mode. 

 
 

 - Half Auto Mode 

 

In Half Auto Mode, the   and 

 buttons can be used to pre-select 

the desired beam heading.  The heading displayed on the 
controller will rapidly change in the direction of desired rotation.  
Once the desired beam heading is shown on the display, release 
the key.  Approximately ½ of a second after no key presses have 
been detected, the display will revert back to the actual beam 
heading, and rotation towards the desired heading will take place.  
Pressing any key while in transit to the desired heading will cancel 
the action. 

 

 - Auto Mode 

 

In Auto Mode, the controller will respond to commands from 
control software running on an attached computer.  The   and 

 

buttons can still be used as a manual override. 

 

 - Preset Mode (requires optional mouse) 

 

In Preset Mode, the   and   buttons cause rotation as long as 
the buttons are pressed.  With the optional mouse attached, the 
six preset buttons can be used to select a desired beam heading. 
Preset beam heading values are set in Setup Mode 

Summary of Contents for AlfaSpid






















Reviews: