background image

 

Installation 

 

 

 

 

Algas-SDI Operation and Maintenance Manual – P/N – 54000 

2-6

 

 

 

CAUTION 

 

The  entire installation must be leak tested prior to operating the 

system. 

 

NOTE 

 

Do not connect this vaporizer to a storage tank that has been used 

in vapor withdrawal service until the tank has been emptied and all 

sediment and heavy ends have been cleaned from it. 

 

 

LI

QUID INLET

 

 

NOTE 

 

Do not install a check valve in the supply line between the tank and 

the vaporizer.  Liquid must be able to flow both ways in that line. 

 

 

1.  Ahead of the vaporizer inlet, install a 60-mesh strainer of equivalent size to 

that of the vaporizer inlet connection. 

2.  Install a UL listed shut-off valve with a Minimum 250psi  (17.24  bar)  gas 

pressure rating 

3.  The liquid line from the storage tank to the vaporizer should be of sufficient 

size to supply the vaporizer at full capacity with a maximum pressure drop of 

less than the hydrostatic head pressure (

see

 

NFPA 54

). 

4.  Connect the vaporizer to the storage tank. 

L

IQUID SUPPLY LINE 

(

see Figure

 3

)

 

 

 

 

             The liquid supply line should be adequately sized for the service. 

 

Table 2 

– Recommended Liquid Supply Line Size (Nominal Pipe Size)

 

Liquid Line Length Ft. (m) 

Up to 50 (15)  50-150 (15-36)  150-250 (36-76) 

160H Vaporizers 

1” (DN25) 

1-1/4” (DN 32)  1-1/2” (DN40) 

320H Vaporizers 

1-1/4” (DN 32)  1-1/2” (DN40) 

2” (DN50) 

480H Vaporizers 

1-1/4” (DN 32)  1-1/2” (DN40) 

2” (DN50) 

640H Vaporizers 

2” (DN50) 

2” (DN50) 

2” (DN50) 

800H Vaporizers 

2” (DN50) 

2” (DN50) 

2” (DN50) 

 

VAPOR DISTRIBUTION

 LINE 

(

see Figure 3

)

 

 

 

 

 

           The vapor distribution line should be adequately sized for the service. 

 

Table 3 

– Recommended Vapor Distribution Line Size (Nominal Pipe Size)

 

Gas Line Length Ft. (m) 

Up to 50 (15)  50-150 (15-36)  150-250 (36-76) 

160H Vaporizers 

1-1/4” (DN 32)  1-1/2” (DN40) 

2” (DN50) 

320H Vaporizers 

1-1/4” (DN 32)  1-1/2” (DN40) 

2” (DN50) 

480H Vaporizers 

1-1/4” (DN 32)  1-1/2” (DN40) 

2” (DN50) 

640H Vaporizers 

1-1/2” (DN40) 

2” (DN50) 

3” (DN80) 

800H Vaporizers 

1-1/2” (DN40) 

2” (DN50) 

3” (DN80) 

 

 

Summary of Contents for 160H



























































Reviews: