background image

Manual 

Mobile Timing MT1 

 

 

- 2 - 

Important Information 

General 

Before using your 

ALGE-TIMING

 device read the complete manual carefully. It is part of the device and 

contains important information about installation, safety and its intended use. This manual cannot cover 
all conceivable applications. For further information or in case of problems that are mentioned not at all 
or not sufficiently detailed, please contact your 

ALGE-TIMING

 representative. You can find contact details 

on our homepage 

www.alge-timing.com

 

Safety 

Apart from the information of this manual all general safety and accident prevention regulations of the 
legislator must be taken into account. 
The device must only be used by trained persons. The setting-up and installation must only be executed 
according to the manufacturer’s data. 

Intended Use 

The device must only be used for its intended applications. Technical modifications and any misuse are 
prohibited because of the risks involved! 

ALGE-TIMING

 is not liable for damages that are caused by im-

proper use or incorrect operation. 

Power supply 

The stated voltage on the type plate must correspond to voltage of the power source. Check all connec-
tions and plugs before usage. Damaged connection wires must be replaced immediately by an author-
ized electrician. The device must only be connected to an electric supply that has been installed by an 
electrician according to IEC 60364-1. Never touch the mains plug with wet hands! Never touch live 
parts! 

Cleaning 

Detergents can cause damage. Never submerge in water or open. The cleaning must not be carried out 
by hose or high-pressure (risk of short circuits or other damage). 

Liability Limitations 

All technical information, data and information for installation and  operation correspond to the latest 
status at time of printing and are made in all conscience considering our past experience and 
knowledge. Information, pictures and description do not entitle to base any claims. The manufacturer is 
not liable for damage due to failure to observe the manual, improper use, incorrect repairs, technical 
modifications, use of unauthorized spare parts. Translations are made in all conscience. We assume no 
liability for translation mistakes, even if the translation is carried out by us or on our behalf. 

Disposal 

If a label is placed on the device showing a crossed out dustbin on wheels (see drawing), 
the European directive 2002/96/EG applies for this device. 
Please get informed about the applicable regulations for separate collection of electrical 
and electronical waste in your country and do not dispose of the old devices as household 
waste. Correct disposal of old equipment protects the environment and humans against 
negative consequences! 
 

Copyright by 

ALGE-TIMING

 GmbH 

All rights reserved. Any duplication, either in full or in part, requires the prior written consent of the copy-
right holder. 
 
 
 

 

Summary of Contents for Mobile Timing MT1

















Reviews: