background image

 

Wireless Timing Network WTN-DB 

 

 

 

 

-2- 

Important Information 

General 

Before using your 

ALGE-TIMING

 device read the complete manual carefully. It is part of the device and 

contains important information about installation, safety and its intended use. This manual cannot cov-
er all conceivable applications. For further information or in case of problems that are mentioned not at 
all or not sufficiently detailed, please contact your 

ALGE-TIMING

  representative. You can find contact 

details on our homepage 

www.alge-timing.com

 

Safety 

Apart from the information of this manual all general safety and accident prevention regulations of the 
legislator must be taken into account. 
The device must only be used by trained persons. The setting-up and installation must only be exe-
cuted according to the manufacturer’s data. 

Intended Use 

The device must only be used for its intended applications. Technical modifications and any misuse 
are prohibited because of the risks involved! 

ALGE-TIMING

 is not liable for damages that are caused by 

improper use or incorrect operation. 

Power supply 

The stated voltage on the type plate must correspond to voltage of the power source. Check all con-
nections and plugs before usage. Damaged connection wires must be replaced immediately by an au-
thorized electrician. The device must only be connected to an electric supply that has been installed 
by an electrician according to IEC 60364-1. Never touch the mains plug with wet hands! Never touch 
live parts! 

Cleaning 

Please clean the outside of the device only with a smooth cloth. Detergents can cause damage. Never 
submerge in water, never open or clean with wet cloth. The cleaning must not be carried out by hose 
or high-pressure (risk of short circuits or other damage). 

Liability Limitations 

All technical information, data and information for installation and operation correspond to the latest 
status at time of printing and are made in all conscience considering our past experience and 
knowledge. Information, pictures and description do not entitle to base any claims. The manufacturer 
is not liable for damage due to failure to observe the manual, improper use, incorrect repairs, technical 
modifications, use of unauthorized spare parts. Translations are made in all conscience. We assume 
no liability for translation mistakes, even if the translation is carried out by us or on our behalf. 

Disposal 

If a label is placed on the device showing a crossed out dustbin on wheels (see drawing), the 
European directive 2002/96/EG applies for this device. 
Please get informed about the applicable regulations for separate collection of electrical and 
electronical waste in your country and do not dispose of the old devices as household waste. 
Correct disposal of old equipment protects the environment and humans against negative 
consequences! 

Operating ranges and interferences 

The 

ALGE

 WTN operates in 4.2 GHz frequency band, the same as WLAN. This is also used by other 

services. The operating range as well as the operation may be disturbed by devices working at the 
same or neighboring frequencies. 

Copyright by 

ALGE-TIMING 

GmbH 

All rights reserved. Any duplication, either in full or in part, requires the prior written consent of the 
copyright holder. 

Summary of Contents for WTN-DB













Reviews: