background image

 

Wireless Timing Network WTN-DB 

 

 

 

 

-8- 

Operation 

 

3.1  Connecting of the WTN-DB at Display Board 

Connect the 4-pin Amphenol plug at the Amphenol socket of the 

 

ALGE-TIMING display board (e.g. D-LINE, GAZ5). 

 
 
 
 
 
 
 
 
 

3.2  Fastening of WTN-DB at Display Board 

The WTN-DB has a clip to fasten it at the case of the display board. 

 

  open the screw of WTN-DB 

  put holder of WTN-DB between left upper side of display board 

  close screw of WTN-DB so it is fixed to display board 

 
 
 
 
 
 
 
 
 
 
 
 

 

Attention: 

Fix the WTN-DB always in the direction that the cable goes downwards. The side with 
the rotation switch is not water protected and must show to the bottom so no water can 
get into the WTN-DB. If you mount the WTN-DB incorrectly it might be destroyed.  
 

3.3  Power Supply 

The WTN-DB is supplied directly from the display board. The LED next to the rotation 
switch blinks when the WTN-DB gets power supply. 
 

3.4  Switching the WTN-DB On or Off 

It is not necessary to switch this device on or off. It is automatically on when you con-
nect it to an ALGE-display board (e.g. D-LINE) and off when you unplug it. The WTN-
DB has no internal batter! 

Summary of Contents for WTN-DB













Reviews: