ALI PROXE 70, Manual

19

Instructions for installation

REMINDERS FOR THE INSTALLER

The manufacturer will not be liable for any damage or 

injury resulting from failure to observe the following 

rules. 

•

Read this manual carefully. It provides important

information for safe installation, use and

maintenance of the appliance.

•

Installation, conversion to a different type of gas

and appliance maintenance must be carried out by

qualified technicians authorized by the manufacturer,

in compliance with current safety standards and the

instructions given in this manual.

•

Identify the specific appliance model. The model

number is detailed on the packaging and on the

appliance data plate.

•

The appliance must be installed in a well-ventilated

room.

•

Do not obstruct any air vents or drains present on

the appliance.

•

Do not tamper with appliance components.

6. REFERENCE STANDARDS AND LAWS

Install the appliance in compliance with current safety

regulations.

Install the appliance in compliance with current

regulations.

7. HANDLING

The packaging is marked with warning symbols that

indicate the precautions to be taken when handling the

appliance to avoid damage.The appliance must only be

handledusing suitable equipment. If lifting equipment is

used, such as forklift trucks or similar, make sure that the

appliance is in a stable position.

8. UNPACKING

Check the state of the packaging and in the event of

damage, ask the delivery person to inspect the goods.

•

Remove the packaging.

•

Remove the protective film from the exterior and

interior panels. Use a suitable solvent to remove any

residual adhesive from the panels.

9. POSITIONING

•

The overall dimensions of the appliance and the

position of connections are given on the installation

diagram at the start of this manual.

•

The appliance can be installed singly or in

combination with other appliances in the same

product range.

•

The appliance is not suitable for integrated installation. 

•

Position the appliance at least 10 cm from adjacent

walls. This distance can be reduced in the presence

of non-combustible walls or heat-insulated walls.

APPLIANCE ASSEMBLY WITH BASE 

Follow the instructions provided with the type of support 

utilized.

JOINING APPLIANCES TOGETHER IN LINE 

•

Place the appliances side by side and adjust the

tops to the same height.

•

Unite the appliances using the special unionjoint-

coverings supplied upon request

11. CONNECTIONS

The position and dimensions of connections are given in

the installation diagram at the start of this manual.

ELECTRICAL CONNECTIONS

Check that the appliance is designed to operate at the 

voltage and frequency of the power supply present on 

site. Check the details given on the appliance data plate.

If used, the symbol 

 indicates:

CAUTION - HAZARDOUS VOLTAGE. 

•

Install an adequately rated omnipolar circuit-breaker

upline of the appliance in an easily accessible point,

in compliance with installation regulations; the

circuit breaker must guarantee immediate omnipolar

disconnection from the mains, with a minimum

contact opening that allows complete disconnection

in overvoltage category III conditions. The maximum

permitted current dispersion is 1mA/kW.

•

For electrical connection, use a rubber-sheathed

flexible cable which is oil resistant, type H05RN-F or

H07RN-F, for cable size consult the technical data

table.

•

Connect the power supply cable to the terminal

board as shown in the wiring diagram supplied with

the appliance.

•

Secure the power supply cable with the cable clamp.

•

Protect the power supply cable on the outside of the

appliance with a rigid plastic or metal pipe.

•

If the power supply cable is damaged, it must be

replaced by the manufacturer or the technical after-

sales service or, in any case, by a suitably qualified

technician, so as to avoid any risk whatsoever.

PROTECTIVE EARTH AND EARTH BONDING 

CONNECTIONS

Connect the appliance to an efficient ground circuit. 

Connect the earth conductor to the terminal with the 
symbol

 located next to the main terminal board. 

Connect the metal structure of the appliance to the 

equipotential node. Connect the conductor to the terminal 
with the symbol 

 on the outside part of the bottom. 

This symbol indicates that the appliance must be 

included in an equipotential system connected in 

compliance with current regulations.

CONNECTION TO THE WATER SUPPLY 

The appliance must be connected to a potable water 

supply.

•

Install a mechanical filter and a shut-off valve

upstream of the appliance in an easily accessible

point.

•

Make sure the water circuit is free from ferrous

particles before connecting the filter and the

appliance.