background image

 

 
 

Aliaro reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. 

 

 

www.aliaro.com 

The SLSC modules is mounted in an AL-1020U chassis with the recommended cooling 
clearances and using a power supply that meets the specifications provided in the chassis user 
guide. For the entire temperature range of the chassis.  

Note These specifications only apply to the product as provided by Aliaro. Modifications 
to the module may invalidate these. Be certain to verify the performance of modified 
modules.  

Caution Observe all instructions and cautions in the user documentation. Using the 
model in a manner not specified can damage the model and compromise the built-in 
safety protection. Return damaged models to Aliaro for repair. 

Environmental Characteristics 

Temperature and Humidity 
Operating temperature 

0 °C to 40 °C 

Storage temperature range 

-40 °C to 85 °C 

Operating relative humidity range 

10% to 90%, noncondensing 

Storage relative humidity range 

5% to 95%, noncondensing 

 

Safety Guidelines 

Caution Ensure that hazardous voltage wiring is performed only by qualified personnel 
adhering to local electrical standards. 

Caution Do not mix hazardous voltage circuits and human-accessible circuits on the 
same module 

Caution When device terminals are hazardous voltage LIVE, you must ensure that 
devices and circuits connected to the device are properly insulated from human contact. 

 

Caution All wiring must be insulated for the highest voltage used. 

 

Product Certifications and Declarations 

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance 
information. To obtain product certifications and the DoC for Aliaro products, visit ni.com/  

Environmental Guidelines 

Notice This model is intended for use in indoor applications only

 

 

Summary of Contents for AL-1020U

















Reviews: