08-19-04 Z08-02830A
16 . Do not start the burner unless a full flow of water is
coming from the wand. Air leaks or insufficient water
to the machine means less than full flow of water
through the coil. This could cause hose failure and
burns to the operator.
17 . Do not start the machine unless the gun assembly is
firmly gripped by the machine operator. Failure to do
this could result in injury from flying hose and gun
assembly.
18 . Always point the gun assembly in a safe direction
and do not direct spray on the cleaner.
1. All guards, shields, and covers must be
replaced after adjustments are made
to prevent accidental contact with
hazardous parts.
2. Drive belts must be inspected and tightened periodically
to operate at optimum levels.
3. Inspect machine for damaged or worn components and
repair or replace to avoid potential hazards. Do not
operate the machine if any mechanical failure is noted
or suspected.
4. Always use the correct size spray tip specified in the
GENERAL section of the
MODEL SPECIFICATIONS
or
MODEL EXPLODED VIEW
.
1. This machine must be electrically grounded.
Failure to have the machine grounded may
result in the operator being electrically
shocked and even death.
2. Do not plug–in or un–plug machine with wet hands.
3. Keep power cords and connections (connectors) out
of water.
4. If an extension cord must be used to operate this
machine, it should be as short as possible. The
extension cord must be properly sized and fitted with
a grounding type plug and receptacle.
5. All wiring and electrical connections should comply
with the National Electrical Code (NEC) and with local
codes and practices.
6. Fuses or circuit breakers should be compatible with
machine requirements. (See ELECTRICAL section
of
MODEL
SPECIFICATIONS
for power
requirements.)
7. High voltage may be present within this machine.
Servicing should only be performed by properly
trained personnel.
1.
Use only fuel #1 or #2 diesel. The use of incor-
rect fuel may result in fire or explosion and severe
injury to the operator.
2. Do not refuel machine while it is running or hot. Allow
it to cool sufficiently to prevent ignition of any spilled
fuel. Clean up any spilled fuel before resuming opera-
tion.
3. Fuel burning equipment must have proper ventilation
for cooling, combustion air, and exhausting of com-
bustion products.
4. Stacking, where required, must be installed in accor-
dance with all local codes. A draft diverter must be
installed on a machine connected to an exhaust stack
to prevent improper operation.
5. Where stacking is not required, provide adequate ven-
tilations to prevent any possible accumulation of haz-
ardous fumes.
6. Personnel trained in and familiar with the type of equip-
ment being serviced should only perform adjustments
to fuel burning equipment.
SAVE THESE SAFETY
INSTRUCTIONS
4
WARNING:
RISK OF INJECTION OR SEVERE
INJURY. KEEP CLEAR OF NOZZLE. DO NOT DIRECT
DISCHARGE STREAM AT PERSONS. THIS EQUIPMENT
IS TO BE USED ONLY BY TRAINED OPERATORS.
AVERTISSEMENT:
RISQUE D’INJECTION ET DE
BLESSURES GRAVES. SE TENIR À L’ÉCART DU JET.
NE PAS DIRIGER LE JET DE SOTIE VERS D’AUTRES
PERSONNES CONFIER L’UTILISATION LE JET DE
SOTIE VERS D’AUTRES PERSONNES. CONFIER
L’UTILISATION DE CE MATÉRIEL À UN OPÉRATEUR
QUALIFIÉ.
WARNING:
DO NOT USE GASOLINE,
CRANKCASE DRAININGS, OR OIL
CONTAINING GASOLINE OR SOLVENTS.
AVERTISSEMENT:
NE PAS UTILISER
D’ESSENCE DE PRODUITS DE VIDANGE NI
MECHANICAL SAFETY
ELECTRICAL SAFETY
FUEL SAEFTY
08-15-03 Z08-02830
Summary of Contents for 3102 Series
