background image

20

DIP SWITCH FUNCTIONS

1     2    3    4     5    6     7    8

-----------------------OPEN------------------------

TIMER 

RADIO

SINGLE/DUAL 

FAIL SC/SF

1-PASS

SLAVE

AUTO OPEN

OPEN IN/OUT

OFF     ON

NOTE:

 IF ANY CHANGES ARE 

MADE TO THE DIPSWITCHES 

WITH THE POWER ON, PRESS 

THE 

MAIN RESET

 BUTTON TO 

RECOGNIZE THE CHANGE.

TIMER

TIMER

 switch 

“ON”

 activates the automatic close 

timer.

RADIO

RADIO 

switch 

“ON”

 allows the radio receiver to 

override the automatic close timer.

SINGLE/DUAL

SINGLE/DUAL 

switch 

“ON”

 is for a dual gate application.

SINGLE/DUAL

 switch 

“OFF”

 is for a single gate

application.

FAIL SC/SF

FAIL SC/SF 

switch 

“ON”

 is for fail safe operation. Upon

power failure, board will monitor battery voltage to make

sure the gate opens before battery completely

drains. 

FAIL SC/SF

 switch 

“OFF” 

is for fail secure

operation. Upon power failure, gate will run until

the battery is low and lock closed.  

1-PASS

1-PASS 

switch 

“ON”

 allows the gate to open until

one vehicle goes over the safety loop. Once the 

vehicle has cleared the loop, the gate will stop and 

close. If a second vehicle goes over the loop while

the gate is closing, the gate will stop. The vehicle

must get off of the loop before the gate continues to

close, forcing the second vehicle to present valid 

credentials. This is a true one pass, anti-tailgating

feature to be used with safety loops.

SLAVE

SLAVE 

is mislabeled on this board version. Use the 

SINGLE/DUAL 

switch to determine single or dual

application. The 

SLAVE 

switch works as an OSC

feature. 

“ON”

 allows the radio receiver to stop and reverse

the gate in any direction. During a cycle, the first signal

stops the gate. A second signal reverses the gate.

AUTO OPEN

AUTO OPEN 

switch 

“ON”

 allows the gate to open

automatically upon power interruption. This feature is used 

in areas where the fire department requires the 

gate open automatically after a power outage.

OPEN IN/OUT

OPEN IN/OUT 

switch 

“ON”

 is used for push to open

installations. The 

“OFF”

 position is used for pull to open

installations.  

O

U

R

3

6

B

S3

O

U

R

3

6

B

S3

O

U

R

3

6

B

S3

ALL-O-MATIC INC.

<ENG.      ESP.>

CMX-309FB  C

8.0000 M

535202

CMX-309FB  C

8.0000 M

535202

CMX-309FB  C

8.0000 M

535202

1     2    3    4     5    6     7    8

-----------------------OPEN------------------------

5

5

MOT

OR 1

MOT

OR 2

SINGLE/DUAL

IN/OUT

24V AC
LINE IN

EXTERNAL

S/N:

DATE:

O

U

R

3

6

B

S3

O

U

R

3

6

B

S3

O

U

R

3

6

B

S3

OPEN 

ERD

CLOSE

ERD

TIMER

MON_12/24VDC

MON_CLOSE

MON_OPEN
STOP CMD

COMMON

COMMON

Summary of Contents for TORO 24



































Reviews: