background image

3.5KW Generator

8

General Precautions (cont’d)

Personal Safety (cont’d)

z

Avoid accidental starting. Make sure the power switch is in its “OFF” 
position, and disconnect the spark plug wWire when not in use.

z

Remove adjusting keys or wrenches before turning the generator on. A 
wrench or a key that is left attached to a rotating part of the generator 
may result in personal injury.

z

Do not overreach. Keep proper footing and balance at all times.

z

Use safety equipment. Always wear eye protection. Wear ANSI 
approved safety impact eye goggles. Dust mask, non-skid safety shoes, 
hard hat, or hearing protection must be used for appropriate conditions.

z

Do not force the generator. Use the correct generator for your 
application. The correct generator will do the job better and safer at the 
rate for which it is designed.

z

Do not use the generator if the power switch does not turn it on or off. 
Any generator that cannot be controlled with the power switch is 
dangerous and must be replaced.

Generator Use and Care

z

Make sure the power switch is in its “OFF” position and disconnect the 
spark plug wire before making any adjustment, changing accessories, or 
storing the generator. Such preventive safety measures reduce the risk 
of starting the generator accidentally.

z

Store idle generators out of reach of children and other untrained 
persons. Generators are dangerous in the hands of untrained users.

z

Maintain generators with care. Do not use damaged generator. Tag 
damaged generators “Do not use” until repaired.

z

Check for misalignment or binding of moving parts, breakage of parts, 
and any other condition that may affect the generator’s operation. If 
damaged, have the generator serviced before using. Many accidents 
are caused by poorly maintained generators.

z

Use only accessories that are recommended by the manufacturer for 
your model. Accessories that may be suitable for one generator may 
become hazardous when used on another generator.

Summary of Contents for APG3001































Reviews: