background image

 

10

 

EPO (Emergency Power Off) Option 

The output power can be disabled in an emergency by closing a switch connected to the EPO. 

Adhere to national and local electrical codes when wiring. 

Rockwell Automation recommends Allen-Bradley Catalog Number 800F Emergency Stop Operator 
as the interface to the EPO to connector. 

The switch should be connected in a normally open switch contact. External voltage is not required; 
the switch is driven by 12 V internal supply. In closed condition, 2m A of current are drawn. 
The EPO switch is internally powered by the UPS for use with non-powered switch circuit breakers. 

 

The EPO circuit is considered a Class 2 circuit, (UL, CSA standards) and an SELV circuit (IEC 
standard). 

 

Both Class 2 and SELV circuits must be isolated from all primary circuitry. Do not connect any 
circuit to the EPO terminal block unless it can be confirmed that the circuit is Class 2 or SELV. 
If circuit standard cannot be confirmed, use a contact closure switch. 

 

Use one of the following cable types to connect the UPS to the EPO switch: 

 

CL2: Class 2 cable for general use 

 

CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air. 

 

CL2R: Riser cable for use in a vertical run in a floor-to-floor shaft. 

 

CLEX: Limited use cable for use in dwellings and for use in raceways. 

 

For installation in Canada: Use only CSA certified, type ELC (extra-low voltage control cable). 

 

For installation in other countries: Use standard low-voltage cable in accordance with local 
regulations. 

Summary of Contents for 1609-P10000E


















Reviews: