background image

English-8

Power Terminal Block Specifications 

Input Power Conditions 

If drives with internal precharge are used with a disconnect switch to the 
common bus, then an auxiliary contact on the disconnect must be 
connected to a digital input of the drive. The corresponding input 
(parameter A051-A054) must be set to option 29, “Precharge Enable.” 
This provides the proper precharge interlock, guarding against possible 
damage to the drive when connected to a common DC bus.

Frame

Maximum Wire Size 

(1)

Minimum Wire Size 

(1)

Torque

B

5.3 mm

2

 (10 AWG)

1.3 mm

2

 (16 AWG)

1.7-2.2 N-m (16-19 lb.-in.)

C

8.4 mm

2

 (8 AWG)

1.3 mm

2

 (16 AWG)

2.9-3.7 N-m (26-33 lb.-in.)

(1)

Maximum/minimum sizes that the terminal block will accept - these are not 
recommendations.

Input Power Condition

Corrective Action

Low Line Impedance (less than 1% line reactance)

Install Line Reactor

(2)

or Isolation Transformer

or Bus Inductor – 5.5 & 11 kW 
(7.5 & 15 HP) drives only

(2)

Refer to Appendix B of the PowerFlex 40P User Manual for accessory ordering 
information.

Greater than 120 kVA supply transformer

Line has power factor correction capacitors

Install Line Reactor

or Isolation Transformer

Line has frequent power interruptions

Line has intermittent noise spikes in excess of 
6000V (lightning)

Phase to ground voltage exceeds 125% of normal 
line to line voltage

Remove MOV jumper to ground.

or Install Isolation Transformer 
with grounded secondary if 
necessary.

Ungrounded distribution system

240V open delta configuration (stinger leg)

(1)

(1)

For drives applied on an open delta with a middle phase grounded neutral system, the 
phase opposite the phase that is tapped in the middle to the neutral or earth is 
referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified 
throughout the system with red or orange tape on the wire at each connection point. 
The stinger leg should be connected to the center Phase B on the reactor. Refer to the 
PowerFlex 40P User Manual for specific line reactor part numbers.

Install Line Reactor

Common Bus/Precharge Notes

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

sales@aotewell.com

+86-755-8660-6182

http://www.aotewell.com/

All manuals and user guides at all-guides.com

Summary of Contents for PowerFlex 40P























Reviews: