background image

Allen-Bradley, Kinetix, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page

.

Publication 2090-IN012E-EN-P - February 2019

Supersedes Publication 2090-IN012D-EN-P - July  2016

Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

*PN-522270*

PN-522270

Additional Resources

These documents contain additional information concerning related products from Rockwell 
Automation.

You can view or download publications at 

http://www.rockwellautomation.com/global/

literature-library/overview.page

.

Resource

Description

Kinetix Rotary Motion Specifications Technical Data, 
publication 

KNX-TD001

 

Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPS), 
MP-Series™ (Bulletin MPL, MPM, MPF, MPS), Kinetix 6000M (Bulletin 
MDF), and TL-Series™ rotary motors.

Kinetix Motion Accessories Specifications Technical 
Data, publication 

KNX-TD004

 

Product specifications for Bulletin 2090 motor and interface cables, low-
profile connector kits, drive power components, and other servo drive 
accessory items.

Kinetix Motion Control Selection Guide,
publication 

KNX-SG001

 

Overview of Kinetix servo drives, motors, actuators, and motion 
accessories designed to help make initial decisions for the motion 
control products best suited for your system requirements. 

Industrial Automation Wiring and Grounding 
Guidelines, publicatio

1770-4.1

 

Provides general guidelines for installing a Rockwell Automation 
industrial system.

Product Certifications website, 

rok.auto/certifications

Provides declarations of conformity, certificates, and other certification 
details.

Summary of Contents for VPL-SSN









Reviews: