background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

3

9002062 (EN)

Installation/Operation Supplement

Safety Information

Explanation of Safety Messages

Throughout this manual and on machine decals, you 
will find precautionary statements (“DANGER,” 
“WARNING,” and “CAUTION”) followed by specific 
instructions. These precautions are intended for the 
personal safety of the operator, user, servicer, and 
those maintaining the machine.

Additional precautionary statements (“IMPORTANT” 
and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used 
to inform the reader of specific procedures where 
minor machine damage will occur if the procedure 
is not followed.

NOTE: The word “NOTE” is used to communicate 
installation, operation, maintenance or servicing 
information that is important but not hazard 
related.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in 

the INSTALLATION manual for the proper 
grounding of the washer.

3. Do not wash textiles that have been previously 

cleaned in, washed in, soaked in, or spotted with 
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or 
explosive substances as they give off vapors that 
could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or 

other flammable or explosive substances to the 
wash water. These substances give off vapors that 
could ignite or explode.

5. Under certain conditions, hydrogen gas may be 

produced in a hot water system that has not been 
used for two weeks or more. HYDROGEN GAS 
IS EXPLOSIVE. If the hot water system has not 
been used for such a period, before using a 
washing machine or combination washer-dryer, 
turn on all hot water faucets and let the water 
flow from each for several minutes. This will 
release any accumulated hydrogen gas. The gas is 
flammable, do not smoke or use an open flame 
during this time.

6. Do not allow children to play on or in the washer. 

This appliance is not intended for use by young 
children or infirm persons without supervision. 
Young children should be supervised to ensure 
that they do not play with the appliance.

7. Before the washer is removed from service or 

discarded, remove the door to the washing 
compartment.

8. Do not reach into the washer if the wash drum is 

moving.

Indicates an imminently hazardous 
situation that, if not avoided, will cause 
severe personal injury or death.

DANGER

Indicates a hazardous situation that, if not 
avoided, could cause severe personal 
injury or death.

WARNING

Indicates a hazardous situation that, if not 
avoided, may cause minor or moderate 
personal injury or property damage.

CAUTION

To reduce the risk of fire, electric shock, 
serious injury or death to persons when 
using your washer, follow these basic 
precautions:

W023

WARNING

Summary of Contents for NX18BVPA6



















Reviews: