6. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to increase or decrease the value of the active digit
and the START (enter) keypad to enter the value of the digit
and advance to the next digit.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price Decimal Point
Ats dP
This option allows the owner to enable a decimal point to show
up in the vend price at one of two locations. For example, a vend
price of
200
can be display with a decimal point as
2.00
or
0.200
.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable options until
Ats
dP
appears in the display.
4. When
Ats dP
appears in the display, press the START (en-
ter) keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the DELI-
CATES 30 (<) keypad.
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to increase or decrease the value of the parameter.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Coin 1 Value
dEn 1
This option allows the owner to set a specific numerical value for
a coin entered. For example, in the United States the coin value
for one quarter would be measured in cents (25). Therefore, the
coin value entered for one quarter would be 00025.
If the Vend Price 1 is set for “.75”, and the Coin Value is set for
“00025”, the vend price displayed will decrease by 0.25 for each
coin entered and 3 coins will need to be entered to satisfy the
vend price.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable options until
dEn
1
appears in the display.
4. When
dEn 1
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the DELI-
CATES 30 (<) keypad.
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to increase or decrease the value of the active digit
and the START (enter) keypad to enter the value of the digit
and advance to the next digit.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Coin 2 Value
dEn 2
This option allows the owner to set a specific numerical value for
a coin entered when using the dual coin drop. For example, the
coin value for a dollar coin would be measured in cents (1.00).
Therefore, the coin value entered for one dollar coin would be
00100.
If the Vend Price #1 (option 1) is set for
2.00
, and the Coin Value
is set for
00100
, the vend price displayed will decrease by 1.00
for each dollar coin entered and 2 coins will need to be entered to
satisfy the vend price.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable options until
dEn
2
appears in the display.
4. When
dEn 2
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the DELI-
CATES 30 (<) keypad.
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to increase or decrease the value of the active digit
and the START (enter) keypad to enter the value of the digit
and advance to the next digit.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Start Pulse Value
PLSE
This option allows the owner to program the value of the Start
Pulse if used for multiple pulses with an after-market central card
reader or pay system.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
46
Part No. 805405ENR5
Summary of Contents for BT3JGASG403UW01
Page 2: ......
