Allied Air 80G1UH2V Installation Instructions Manual Download | Manualshive

Page: 1 / 41

background image

506471-01

Page 1 of 41

Issue 1034

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in
manuals, be alert to the potential for personal injury or death.

Improper installation, adjustment, alteration, service or
maintenance can cause property damage, personal injury
or loss of life. Installation and service must be performed
by a licensed professional installer (or equivalent), service
agency or the gas supplier.

WARNING

Manufactured By

Allied Air Enterprises, Inc.

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This manual must be left with the homeowner for future reference.

INSTALLATION INSTRUCTIONS

A80UH2V & 80G1UH2V

Warm Air Gas Furnace

Upflow / Horizontal Left and Right Air Discharge

TABLE OF CONTENTS

Unit Dimensions ............................................................ 2
A80UH2V & 80G1UH2V Parts Arrangement ................ 3
A80UH2V & 80G1UH2V Gas Furnace ......................... 4
Shipping and Packing List ............................................ 4
Safety Information ......................................................... 4
Use of Furnace as a Construction Heater .................... 5
General ......................................................................... 6
Combustion, Dilution, Ventilation Air ............................. 6
Setting Equipment ........................................................ 9
Filters .......................................................................... 12
Duct System ................................................................ 12
Venting ........................................................................ 13

Gas Piping .................................................................. 23
Electrical ..................................................................... 25
Thermostat .................................................................. 27
Unit Start-Up ............................................................... 30
Heating Sequence of Operation ................................. 31
Gas Pressure Adjustment ........................................... 33
High Altitude ................................................................ 34
Other Unit Adjustments ............................................... 34
Maintenance ............................................................... 33
Repair Parts List ......................................................... 37
Wiring Diagram ........................................................... 38

*506471-01*

As with any mechanical equipment, personal injury can
result from contact with sharp sheet metal edges. Be
careful when you handle this equipment.

CAUTION

1
2
3
...
»

Summary of Contents for 80G1UH2V










































Reviews:

No comments

Related manuals for 80G1UH2V

Brand: Empire Pages: 18

Brand: Ingersoll-Rand Pages: 40

Brand: Fluke Pages: 47

Brand: Allied Pages: 57

Brand: Allied Pages: 56

Brand: Allied Pages: 54

Brand: York Pages: 8

Brand: Barnstead|Thermolyne Pages: 12

Brand: United States Stove Pages: 24

Brand: Unitary products group Pages: 16

Brand: Unitary products group Pages: 2

Brand: ICP Pages: 16

Brand: Thermo Pride Pages: 29

Brand: Thermo Pride Pages: 27

Brand: Thermo Pride Pages: 47

Brand: KERR Pages: 24

Brand: KERR Pages: 20

Brand: ECR International Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands