background image

 

  AT-FS750/24-41 Web User Interface Manual 

6-23 

 

Parameter 

 

Description 

Select 

  Select a line to change the configuration. 

IGMP Snooping Status 

  To enable or disable IGMP Snooping globally. Default is enabled. 

Operational Status 

  Specify the operational status of IGMP snooping function. 

Snooping Mode 

  Speficy the Snooping mode of IGMP snooping function. 

Report Forwarding 

  Specify which port to forward the IGMP report. Select 

All Ports

 to forward the 

report to all ports, 

Router  Ports

 to forward the reports to IGMP router ports 

only. Default is Router Ports. 

Retry Count (1~5) 

  To  set  the  maximum  retries  for  group  specific  queries  which  sent  to  a  port 

received a IGMPv2 leave message. The possible number is 1-5 times. Default 
is 2. 

Query Transmit On TC 

  Specify  if  the  IGMP  queries  will  still  be  sent  when  STP  topology  change 

happens.  Select 

Enable

  to  transmit  the  queriers, 

Disable

d  not  to  transmit. 

Default is Disabled. 

 
Click 

Apply

 to submit the changes. 

 

IGMP Snooping Timer Configuration 

This page is to configure the IGMP Snooing timers. 

 

Figure 60 – Layer2 Management > IGMP Snooping > Timer Configuration 

 

Parameter 

 

Description 

Router 

Port 

Purge 

Interval (60~600 Secs) 

  To set the time-out period that an IGMP multicast router port hasn

‟t received 

IGMP router control packet, it will be deleted. Default is 125 seconds. 

Group-Member 

Port 

Purge 

Interval 

(130~2335 Secs) 

  To  set  the  purge  interval  that  an  IGMP  member  port 

hasn‟t‟  received  IGMP 

report packet, it will be deleted. Default is 260 seconds. 

Report 

Forward 

Interval (1~25 Secs) 

  To  set  the  time  interval  that  IGMPv2  report  of  the  same  group  will  not  be 

forwarded to the router ports. Default is 5 seconds. 

Group  Query  Interval 
(1~5 Secs) 

  To  set  up  the  time  interval  to  send  the  group  specific  query.  Default  is  2 

seconds. 

Querier  Query  Intercal 
(60~600 Secs) 

  To  set  up  the  time  interval  to  send  the  IGMP  general  query.  Default  is  125 

seconds. 

 
Click 

Apply

 to submit the changes, 

Reset

 to clear the values just inputed. 

 

IGMP Snooping Interface Configuration 

This page is to cunfigure the VLAN bassis IGMP snooping settings. 
 

Summary of Contents for AT-FS24-41











































































Reviews: