background image

Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches

3

Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C

288MB RDRAM was initialised incorrectly, resulting in unpredictable 
behaviour. This issue has been resolved.

 

Inuse

 DHCP entries (that are displayed in the SHOW DHCP CLIENT 

command) will now expire and be reclaimed.

It was possible to add the same IPv6 prefix to different IPv6 interfaces. This 
issue has been resolved.

The wrong error message was displayed if PPP compression over L2TP was 
attempted. The correct message is now generated, stating that the CREATE 
PPP command is invalid.

Some parameters in the SET IP IGMP command had incorrect ranges. This 
issue has been resolved. The correct ranges are:

SET IP IGMP 

[LMQI=1..255] [LMQC=1..5]

 

[QUERYINTERVAL=1..65535] 

[QUERYRESPONSEINTERVAL=1..255]

 

[ROBUSTNESS=1..5]

 [TIMEOUT=1..65535]

If multiple IPv6 interfaces shared the same link-local address, pings to the 
link-local address sometimes failed. This issue has been resolved.

Loading files to NVS caused a fatal error. This issue has been resolved.

A warning was not given if the egress limit for a port was not set to a 
multiple of 64. This issue has been resolved.

ARP entries on the SwitchBlade 4000 Series Switch controller card are now 
updated correctly if a device changes to a different line card.

The source net mask has been removed from DVMRP 

prune

graft

 and 

graft-ack 

messages.

Executing the PING command sometimes caused a memory leak. This issue 
has been resolved.

Untagged IGMP packets were erroneously sent out of tagged ports. This 
issue has been resolved.

PCR: 02492

Module: SWI

Network affecting: No

PCR: 02493

Module: DHCP

Network affecting: No

PCR: 02494

Module: IPv6

Network affecting: No

PCR: 02497

Module: PPP

Network affecting: No

PCR: 02499

Module: IPG

Network affecting: No

PCR: 02502

Module: Ping, IPv6

Network affecting: No

PCR: 02503

Module: NVS

Network affecting: No

PCR: 02504

Module: SWI

Network affecting: No

PCR: 02507

Module: SWI

Network affecting: No

PCR: 02509

Module: DVMRP

Network affecting: No

PCR: 02511

Module: Ping

Network affecting: No

PCR: 02516

Module: IPG

Network affecting: No

Summary of Contents for SB244-03









Reviews: