Allied 96G2DFV Installation Instructions Manual Download

Page: 13 / 53

507962-01

Page 13 of 53

Issue 2149

furnace is installed. The furnace access panel must always

be in place when the furnace is operating and it must not

allow leaks into the supply air duct system.

Return Air Plenum

NOTE:

Return air must not be drawn from a room where

this furnace, or any other gas-fueled appliance (i.e., water

heater), or carbon monoxide-producing device (i.e., wood

fireplace) is installed.

When return air is drawn from a room, a negative pressure

is created in the room. If a gas appliance is operating in

a room with negative pressure, the flue products can be

pulled back down the vent pipe and into the room. This

reverse flow of the flue gas may result in incomplete

combustion and the formation of carbon monoxide gas.

This toxic gas might then be distributed throughout the

house by the furnace duct system.

Use fiberglass sealing strips, caulking, or equivalent

sealing method between the plenum and the furnace

cabinet to ensure a tight seal. If a filter is installed, size the

return air duct to fit the filter frame.

Pipe & Fittings Specifications

All pipe, fittings, primer and solvent cement must conform

with American National Standard Institute and the American

Society for Testing and Materials (ANSI/ASTM) standards.

The solvent shall be free flowing and contain no lumps,

undissolved particles or any foreign matter that adversely

affects the joint strength or chemical resistance of the

cement. The cement shall show no gelation, stratification,

or separation that cannot be removed by stirring. Refer to

Table 4 below for approved piping and fitting materials.

Solvent cements for plastic pipe are flammable liquids

and should be kept away from all sources of ignition.

Do not use excessive amounts of solvent cement when

making joints. Good ventilation should be maintained to

reduce fire hazard and to minimize breathing of solvent

vapors. Avoid contact of cement with skin and eyes.

CAUTION

The exhaust and intake connections are made of PVC.

Use PVC primer and solvent cement when using PVC

vent pipe. When using ABS vent pipe, use transitional

solvent cement to make connections to the PVC fitting

in the unit.

IMPORTANT

Table 4.

Piping and Fittings Specifications

Schedule 40 PVC (Pipe)

D1785

Schedule 40 PVC (Cellular Core Pipe)

F891

Schedule 40 PVC (Fittings)

D2466

Schedule 40 CPVC (Pipe)

F441

Schedule 40 CPVC (Fittings)

F438

SDR-21 PVC or SDR-26 PVC (Pipe)

D2241

SDR-21 CPVC or SDR-26 CPVC (Pipe)

F442

Schedule 40 ABS Cellular Core DWV

(Pipe)

F628

Schedule 40 ABS (Pipe)

D1527

Schedule 40 ABS (Fittings)

D2468

ABS-DWV (Drain Waste & Vent)

(Pipe & Fittings)

D2661

PVC-DWV (Drain Waste & Vent)

Pipe & Fittings)

D2665

PRIMER & SOLVENT CEMENT

ASTM

SPECIFICATION

PVC & CPVC Primer

F656

PVC Solvent Cement

D2564

CPVC Solvent Cement

F493

ABS Solvent Cement

D2235

PVC/CPVC/ABS All Purpose Cement For

Fittings & Pipe of the same material

D2564, D2235,

F493

ABS to PVC or CPVC Transition Solvent

Cement

D3138

CANADA PIPE & FITTING & SOLVENT

CEMENT

MARKING

PVC & CPVC Pipe and Fittings

ULCS636

PVC & CPVC Solvent Cement
ABS to PVC or CPVC Transition Cement

POLYPROPYLENE VENTING SYSTEM

ULC-S636

PolyPro® by Duravent

InnoFlue® by Centrotherm

ULC-S636

ECCO Polypropylene Vent

ULC-S636

Use PVC primer and solvent cement or ABS solvent

cement meeting ASTM specifications, refer to Table 4.

As an alternate, use all purpose cement, to bond ABS,

PVC, or CPVC pipe when using fittings and pipe made of

the same materials. Use transition solvent cement when

bonding ABS to either PVC or CPVC.

Low temperature solvent cement is recommended during

cooler weather. Metal or plastic strapping may be used as

vent pipe hangers. Uniformly apply a liberal coat of PVC

primer for PVC or use a clean dry cloth for ABS to clean

inside socket surface of fitting and male end of pipe to

depth of fitting socket.

Canadian Applications Only

Pipe, fittings, primer and solvent cement used to vent

(exhaust) this appliance must be certified to ULC S636 and

supplied by a single manufacturer as part of an approved

Summary of Contents for 96G2DFV






















































Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands

Allied 96G2DFV, Installation Instructions Manual

Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands