Allied 96G2DFV Installation Instructions Manual Download

Page: 50 / 53

507962-01

Page 50 of 53

Issue 2149

Service

ELECTRICAL SHOCK, FIRE, OR EXPLOSION

HAZARD.

Failure to follow safety warnings exactly could result in

dangerous operation, serious injury, death or property

damage.

Improper servicing could result in dangerous operation,

serious injury, death, or property damage.

Before servicing, disconnect all electrical power to

furnace.
When servicing controls, label all wires prior to

disconnecting. Take care to reconnect wires correctly.

Verify proper operation after servicing.

WARNING

At the beginning of each heating season, system should

be checked as follows by a qualified service technician:

Blower

Check the blower wheel for debris and clean if necessary.

The blower motors are pre-lubricated for extended bearing

life. No further lubrication is needed.

The blower access panel must be securely in place

when the blower and burners are operating. Gas fumes,

which could contain carbon monoxide, can be drawn

into living space resulting in personal injury or death.

WARNING

Filters

All air filters are installed external to the unit. Filters should

be inspected monthly. Clean or replace the filters when

necessary to ensure proper furnace operation. Table 3 lists

recommended filter sizes.

Exhaust and Air Intake Pipes

Check the exhaust and air intake pipes and all connections

for tightness and to make sure there is no blockage.

NOTE:

After any heavy snow, ice or frozen fog event the

furnace vent pipes may become restricted. Always check

the vent system and remove any snow or ice that may be

obstructing the plastic intake or exhaust pipes.

Electrical

1. Check all wiring for loose connections.
2. Check for the correct voltage at the furnace (furnace

operating). Correct voltage is 120 VAC ± 10%.

3. Check amp-draw on the blower motor with the blower

compartment access panel in place.

Motor Nameplate__________Actual__________

Winterizing and Condensate Trap Care

1. Turn off power to the furnace.

2. Have a shallow pan ready to empty condensate water.
3. Remove the clean out cap from the condensate trap

and empty water. Inspect the trap then reinstall the

clean out cap.

Cleaning Heat Exchanger

If cleaning the heat exchanger becomes necessary,

follow the below procedures and refer to Figure 1 when

disassembling unit. Use papers or protective covering in

front of furnace while removing heat exchanger assembly.

1. Turn off electrical and gas supplies to the furnace.

2.  Remove the furnace access panels.
3.  Disconnect the wires from the gas valve.
4.  Remove  gas  supply  line  connected  to  gas  valve.

Remove gas valve/manifold assembly.

5. Remove sensor wire from sensor. Disconnect 2 pin

plug from the ignitor.

6. Disconnect wires from flame rollout switches.
7. Loosen clamps at vent elbow. Disconnect condensate

drain tubing from flue collar and remove the vent

elbow.

8. Remove four burner box screws at the vestibule panel

and remove burner box. Set burner box assembly

aside.

NOTE:

If necessary, clean burners at this time. Follow

procedures outlined in Burner Cleaning section.

9. Mark and disconnect all combustion air pressure

tubing from cold end header collector box.

10. Mark and remove wires from pressure switches.

Remove pressure switches. Keep tubing attached to

pressure switches.

11. Disconnect the plug from the combustion air inducer.

Remove two screws which secure combustion air

inducer to collector box. Remove combustion air

inducer assembly. Remove ground wire from vest

panel.

12. Remove electrical junction box from the side of the

furnace.

13. Mark and disconnect any remaining wiring to heating

compartment components. Disengage strain relief

bushing and pull wiring and bushing through the hole

in the blower deck.

14. Remove the primary limit from the vestibule panel.
15. Remove two screws from the front cabinet flange at

the blower deck. Spread cabinet sides slightly to allow

clearance for removal of heat exchanger.

Summary of Contents for 96G2DFV






















































Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands

Allied 96G2DFV, Installation Instructions Manual

Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands