Allied 96G2DFV Installation Instructions Manual Download

Page: 34 / 53

507962-01

Page 34 of 53

Issue 2149

Gas Piping

If a flexible gas connector is required or allowed by

the authority that has jurisdiction, black iron pipe shall

be installed at the gas valve and extend outside the

furnace cabinet. The flexible connector can then be

added between the black iron pipe and the gas supply

line.

CAUTION

Do Not exceed 600 in. lbs. (50 ft. lbs.) torque when

attaching the gas piping to the gas valve.

WARNING

1. Gas piping may be routed into the unit through either

the left or right hand side. Supply piping enters into

the gas valve from the side of the valve as shown in

Figure 53.

A low inlet pressure switch in LP/propane applications

is recommended.

IMPORTANT

2. When connecting gas supply, factors such as length

of run, number of fittings and furnace rating must be

considered to avoid excessive pressure drop. Table 10

lists recommended pipe sizes for typical applications.

NOTE:

Use two wrenches when connecting gas piping

to avoid transferring torque to the manifold.

3. Gas piping must not run in or through air ducts,

clothes chutes, chimneys or gas vents, dumb waiters

or elevator shafts. Center gas line through piping hole.

Gas line should not touch side of unit. See Figure 53.

4. Piping should be sloped 1/4 inch per 15 feet (6 mm per

5.6 m) upward toward the gas meter from the furnace.

The piping must be supported at proper intervals,

every 8 to 10 feet (2.44 to 3.05 m), using suitable

hangers or straps. Install a drip leg in vertical pipe runs

to serve as a trap for sediment or condensate.

5. A 1/8” N.P.T. plugged tap or pressure post is located

on the gas valve to facilitate test gauge connection.

In some localities, codes may require installation of a

manual main shut off valve and union (furnished by

installer) external to the unit. Union must be of the

ground joint type.

Compounds used on threaded joints of gas piping must

be resistant to the actions of liquified petroleum gases.

IMPORTANT

Leak Check

After gas piping is completed, carefully check all field-

installed piping connections for gas leaks. Use a

commercially available leak detecting solution specifically

manufactured for leak detection. Never use an open flame

to test for gas leaks.

The furnace must be isolated from the gas supply

system by closing the individual manual shut-off valve

during any gas supply system at pressures greater than

or equal to 1/2 psig (3.48 kPa, 14 inches w.c.). This

furnace and its components are designed, manufactured

and independently certified to comply with all applicable

ANSI/CSA standards. A leak check of the furnace and its

components is not required.

Figure 52.

When testing pressure of gas lines, gas valve must

be disconnected and isolated. Gas Valves can be

damaged if subjected to pressures greater than 1/2 psig

(3.48 kPa).

IMPORTANT

FIRE OR EXPLOSION HAZARD

Failure to follow the safety warnings exactly could

result in serious injury, death, or property damage.

Never use an open flame to test for gas leaks. Check

all connections using a commercially available soap

solution made specifically for leak detection. Some

soaps used for leak detection are corrosive to certain

metals. Carefully rinse piping thoroughly after leak test

has been completed.

WARNING

Summary of Contents for 96G2DFV






















































Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands

Allied 96G2DFV, Installation Instructions Manual

Search results

Summary of Contents for 96G2DFV

Reviews:

Related manuals for 96G2DFV

Brands by name

Popular brands