background image

506941-01

Page 15  of  16

Issue 1148

EQUIPMENT LIMITED WARRANTY

APPLIES IN U.S.A. AND CANADA ONLY

FAILURE TO MAINTAIN YOUR EQUIPMENT WILL VOID THIS WARRANTY.

COVERED EQUIPMENT

The following heating and cooling equipment is covered by the Limited

Warranty:

Oil Furnaces:

LG14.

Unit/Duct Heaters:

LD24 (all 

units), LF24 and TUA (100,000 to 400,000 btuh units).

Evaporator Coils: 

C17.

Air Handlers: 

ACBX32, CB17, CBH17, TAA.

Condensing

 Units: 

4SCU13LC, TSA.

Heat Pumps: 

4SHP13LC, TPA.

Packaged

 Equipment:

KCA, K

G

A

KHA, TCA, TGA, THA, RGE13, RHP13, RCE13.

Electric Heat Sections: 

AECB29, ECH16, EH17, ECH24.

ONE (1) YEAR COVERAGE −− ALL APPLICATIONS

The covered equipment and covered components are warranted by the

manufacturer

 for a period of one (1) year from the 

date of the original unit

installation

, when installed and operated in accordance with the manufac-

turer’s

 recommendations. If, 

during this period, a covered component fails

because of a manufacturing defect, the manufacturer will provide a free

replacement 

part to the owner. The owner must pay shipping charges and

all other costs of warranty service.

EXTENDED COVERAGE

This limited warranty provides extended coverage on the components

outlined

 below. The extended warranty coverage begins with the 

date of

th

e

 original unit installation

 and represents the total warranty period for the

specific

 component.

Heat Exchangers:

KGA and TGA  (Aluminized −− All applications) −− Ten (10) years.

KGA and TGA (Stainless −− All applications) −− Fifteen (15) years.

RGE13, RHP13 and RCE13   −− Ten (10) years.

LF24 and TUA (Aluminized −− All applications) −− Ten (10) years.

LF24 and TUA (Stainless −− All applications) −− Fifteen (15) years.

LD24 (Aluminized −− All applications) −− Two (2) years.

LD24 (Stainless −− All applications) −− Five (5) years.

LG14 (All applications) −− Five (5) years.

Burners:

LG14

 −− Three (3) years.

Compressors:

4SCU13LC, 4SHP13LC −− Five (5) years.

TSA, TPA −− Five (5) years.

KCA, KGA, KHA, TCA, TGA, THA −− Five (5) years.

RGE13, RHP13, RCE13 −− Five (5) years.

NOTE − If the date of original installation cannot be verified, the warranty

period

 will be deemed to begin six (6) months after the date of manufac-

ture.

COMPONENT AVAILABILITY

In

 the event that a component covered by this warranty is no longer available, the

manufacturer will, at its option, provide a free suitable substitute component or

allow

the 

owner to purchase an equivalent new unit at a reduced price of 20 per-

cent of the list price in effect on the date of the failure. The owner must pay ship-

ping charges and all other costs of warranty service.

EXCLUDED COMPONENTS

The following components are not protected by this warranty: cabinets,

cabinet pieces, air filters, driers, refrigerant, belts, wiring, fuses and unit

accessories.

REPAIRS

All repairs of covered components must be made with authorized service

parts by a licensed professional service contractor (or equivalent).

CARE OF EQUIPMENT

This new unit must be properly installed, operated and maintained by a li-

censed

 professional installer (or equivalent) o

r s

e

rv

ic

e

 agency in accordance

with the unit installation, operation and maintenance instructions provided

w

it

h

 each unit. Failure to 

provide

maintenance per the manufacturer’s instruc-

tions 

will void this warranty. The owner may be asked to provide written docu-

mentation

 of annual and other periodic preventive maintenance.

Summary of Contents for RGE Series

















Reviews: