32 / 36 - Nederlandse
6-1622396 - rev. 3 - 21/09/2021
29. WEERGAVE GEHEUGENPLAATS ENKELE ZENDER
TRS
Door het
TRS
-item te openen kunt u de geheugenlocatie bekijken waar een zender is opgeslagen. Om de functie uit te voeren,
opent u het item en bevestigt u dit door lang op de knop “MENU” te drukken.
Houd de knop ingedrukt tot de AFDRUKWEERGAVE ZIE wordt weergegeven en laat de knop los.
Druk op dit punt op een knop van de opgeslagen zender (activeert geen enkele opdracht).
Het display toont de positie in het geheugen gedurende 2 seconden als het was opgeslagen; anders wordt het woord niet gedurende
2 seconden op het display afgedrukt als het niet is opgeslagen.
Na 2 seconden keert het display terug naar het SCHERM ZIE en u kunt de functie met een andere zender laten werken.
Om de functie te verlaten, drukt u op de knop “MENU”, anders verlaat het bedieningspaneel na 15 seconden zonder transmissie
de functie die het woord
Tout
op het display toont.
30. VERWIJDERING ENKELE ZENDER
TRC
Door toegang te krijgen tot de
trC
-stem kunt u één opgeslagen zender uit het geheugen wissen. Om de functie uit te voeren,
opent u het item en bevestigt u dit door lang op de knop “MENU” te drukken.
Houd ingedrukt totdat de waarde
0
op het display wordt afgedrukt en laat de knop los. Selecteer de locatie in het geheugen van
de zender. Houd de knop menu ingedrukt totdat
CLR
op het display wordt weergegeven. Laat de knop los.
Om de functie te verlaten, drukt u kort op de knop “MENU”. Als
ERR
op het display verschijnt, zijn er problemen met het geheugen
(bijvoorbeeld lege positie of losgekoppeld geheugen).
31. RESET GEHEUGEN AFSTANDSBEDIENINGEN
trF
Door toegang te krijgen tot het
trf
-menu kunt u alle geleerde zenders verwijderen. Om de toegang tot het item te resetten,
bevestigt u met de uitgebreide druk op de knop “MENU”.
Houd ingedrukt totdat de waarde
0
op het display wordt afgedrukt en laat de knop los. Druk nogmaals op de knop “MENU” en houd
deze ingedrukt om af te tellen: “d80, d79, ... , d01” voltooid, welke reset wordt uitgevoerd en
don
wordt weergegeven.
31. PARAMETER
SId
Parameter niet in gebruik.
9.10 AFSTELLING VAN DE SLAG VAN DE BOOM / MAST
Voor een correcte afstelling van de slag van de boom / mast houdt u rekening met de werking van de volgende parameters:
• SPnc
= volledig operationele snelheid
• SPLc
= verlaag de snelheid
• LSIc
= amplitude van het gebied voor vertragen
• drac
= Tijd om over te schakelen van SPno naar de lage
snelheid
WAARSCHUWING!
De parameters en de tekening hebben
betrekking op de sluitbeweging van de giek.
LSIc
drac [sec]
SPLc
SPnc
Summary of Contents for 12007336
