26 / 36 - Italiano
6-1622396 - rev. 3 - 21/09/2021
4. SENSIBILITÀ SU OSTACOLO A VELOCITÀ DI RALLENTAMENTO
SEL
(0 – 100%) default = 60%
Regolare la sensibilità su ostacolo nelle aree di rallentamento in modo da ottenere un corretto funzionamento dell’automazione,
intervenendo in caso di ostacolo ma tale da garantire la movimentazione anche nelle condizioni peggiori di funzionamento
(es. inverno, indurimento dei motori dovuti all’usura, etc.). Si consiglia dopo la regolazione del parametro di eseguire una
movimentazione completa di apertura e chiusura, prima di verificare l’intervento su ostacolo. Valori inferiori corrispondono ad una
maggiore spinta sull’ostacolo.
5-6. VELOCITÀ A REGIME
SPno
e
SPnc
(50 – 100 %) default = 100%
Regolare la velocità di regime per assicurare il corretto funzionamento dell’automazione. Con
SPno
si regola la velocità di regime in
fase di apertura, mentre con
SPnc
si regola la velocità di regime in fase di chiusura. È possibile regolare la percentuale di velocità
da un minimo di 50% a un massimo di 100%.
7-8. VELOCITÀ IN RALLENTAMENTO
SPLo
e
SPLc
(10-100 %) default = 30%
Regolare la velocità in rallentamento per assicurare il corretto funzionamento dell’automazione. Con
SPLo
si regola la velocità di
rallentamento in fase di apertura, mentre con
SPLc
si regola la velocità di rallentamento in fase di chiusura. È possibile regolare
la percentuale di velocità da un minimo di 10% a un massimo di 100% della velocità a regime corrispondente (
SPno
/
SPnc
).
9. CONFIGURAZIONE PASSO-PASSO
SbS
(0 - 2) default = 0
È possibile impostare tre modalità di funzionamento per il comando SS:
•
Valore 0 = normale (AP-ST-CH-ST-AP-ST-CH-…).
Tipico funzionamento Step by Step. Durante la movimentazione una pressione di SS comporta l’arresto dell’automazione.
•
Valore 1 = alternato STOP (AP-ST-CH-AP-ST-CH-…).
Funzionamento alternato con STOP in apertura. Durante la movimentazione di apertura una pressione di SS comporta
l’arresto dell’automazione.
•
Valore 2 = alternato (AP-CH-AP-CH-…).
L’utente non ha modo di fermare l’automazione con il comando di SS. Inviando il comando SS si ottiene l’immediata
inversione della marcia.
10. COMPORTAMENTO DOPO BLACKOUT
blt
(0 – 2) default = 0
Determina il comportamento della scheda, al suo riavvio, dopo aver tolto alimentazione (blackout). Nel caso l’asta si trovi in
posizione di aperto o chiuso al momento del blackout, la movimentazione successiva al ripristino della corrente avverrà sempre alla
velocità di regime impostata. Nel caso invece l’asta si trovi in una posizione intermedia, il primo movimento avviene alla velocità
ridotta, fino al raggiungimento del finecorsa.
•
Valore 0 = nessuna azione.
Alla riaccensione l’automazione rimane ferma fino alla ricezione di un comando utente. Se il comando è un PASSO-PASSO,
il primo movimento è in apertura.
•
Valore 1 = esegue apertura.
La centrale, appena riavviata, comanda autonomamente una apertura. In questo caso NON vengono considerati i tempi di
richiusura automatica impostati.
•
Valore 2 = esegue chiusura.
La centrale, appena riavviata, comanda autonomamente una apertura a velocità ridotta e subito dopo una chiusura a
velocità di regime.
11-12. AMPIEZZA RALLENTAMENTO
LSIo
e
LSIc
(0 – 100 %) default = 25%
Con questo parametro è possibile definire l’ampiezza dei rallentamenti ed eventualmente la loro esclusione (
LSI
= 0). Con
LSIo
si regola l’ampiezza di rallentamento in fase di apertura, mentre con
LSIc
si regola l’ampiezza di rallentamento in fase di chiusura.
13 ANTISLITTAMENTO / TEMPO EXTRA
ASL
(0 – 300 secondi) default = 25%
Parametro per compensare un eventuale slittamento del motore, vengono aggiunti
ASL
secondi ai tempi di movimentazione per
assicurare la completa movimentazione dell’automazione in ogni situazione.
14. MODALITÀ DI UTILIZZO DELL’ENCODER
ENC
(0 – 3) default = 3
Parametro per stabilire in quale momento viene utilizzato l’encoder del motore.
•
Valore 0 = encoder non utilizzato
•
Valore 1 = Rileva ostacolo e posizione
•
Valore 2 = Rileva ostacolo
•
Valore 3 = Rileva posizione
Summary of Contents for 12007336
