background image

 

19 

Chapter 4: System Administration 

Overview 

The ALLNET IP storage provides an easily accessible Web Administration 
Interface
. With it, you can configure and monitor the ALLNET IP storage anywhere 
on the network. 
 

Web Administration Interface 

Make sure your network is connected to the Internet. To access ALLNET IP storage 
Web Administration Interface
 

1.

 

Type the ALLNET IP storage IP address into your browser. (Default IP 
address is 

http://192.168.1.100

)     

 

 

 

 

2.

 

Login to the system using the administrator user name and password. The 
factory defaults are:   

 

User Name: 

admin

 

Password: 

admin

 

 

※ 

If you changed your password in the setup wizard, use the new password. 

 

NOTE 

Your computer’s network IP address must be on the same subnet as the ALLNET 
IP storage. If the ALLNET IP storage has default IP address of 192.168.1.100, 
your managing PC IP address must be 192.168.1.x, where x is a number 
between 1 and 254, but not 100. 

Summary of Contents for ALL-NAS1000










































































































































Reviews: