background image

ALL168255 QIG English 

ALL168255 Quick Installation Guide      © 2012 ALLNET GmbH    All rights reserved          Page 7                                             

 

 

Specification 

Items 

Description 

PHY Rate 

500Mbps 

Effect Data Rate 

TCP: Up to 95 Mbps effective throughput   

UDP: Up to 95 Mbps effective throughput 

Frequency Band 

2~68 MHz (With Mask) 

Access Methods 

priority-based CSMA/CA channel access schemes maximize efficiency and 

throughput 

Qos 

 

– Integrated Quality of Service (QoS) Enhancements   

 

– Hardware Packet Classifiers for ToS, CoS and IP Port Number 

 

– Supports IGMP managed multicast sessions 

Modulation 

OFDM (QAM 8/16/64/256/1024/4096, QPSK, BPSK, ROBO) 

Standards 

IEEE 802.3, HomePlug AV Protocol Compliance with HomePlug 1.0 coexistence 

capability 

OS 

Microsoft Windows® 2000, XP, Vista ,Windows 7 (for utility-program only) 

Nodes 

Up to 8 total devices 

IGMP 

IGMP supports IGMP managed multicast sessions 

 

Encryption 

128-bit AES Link Encryption with key management 

Push button 
 

NID/RST button 

Port 

One 100 Mpbs Ethernet Port 

Distance 

AC Wire : 200 meters distance max. 

LEDs 

PWR (Green) PLC (Green/Orange/Red, throughput indicator)   

ETH (Green)

 

Environment 

Temperature 

Operating : 0~40 

 

Storage : -20~60 

 

Relative Humidity 

Operating : 10~85% Non-Condensing

 

Storage : 5~90% Non-Condensing

 

Power Source 

100 ~ 240 VAC 50/60Hz 

Power 
Consumption 

ca. 2W (Normal mode), less than 0.5W (Standby mode) 

Certification 

CE 

S

PECIFICATION

 

Summary of Contents for ALL168255













Reviews: