background image

INTRODUCTION

This oil lubricated air compressor is designed for Household Use Only and is not intended for commercial applications. It is well suited for do-it-
yourselfers with a variety of automotive and home uses.

This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps
described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest product information
available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice. 

SAFETY ALERT

READ AND UNDERSTAND THIS ENTIRE INSTRUCTION MANUAL BEFORE ATTEMPTING 

TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THIS AIR COMPRESSOR. FAILURE TO COMPLY 

WITH THE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE!

The following signal words are used to emphasize safety warnings that must be followed when using this air compressor:

Indicates an imminently hazardous situation that, if not avoided, 

WILL

result in death or serious injury.

Indicates a potentially hazardous situation that, if not avoided, 

COULD

result in death or serious injury.

Indicates a potentially hazardous situation that, if not avoided, 

MAY

result in minor or moderate injury.

Indicates important information which if not followed, 

MAY

cause damage to equipment.

UNPACKING & INSPECTION

After opening the carton, unpack your new air compressor and related parts & accessories. Please inspect it carefully for any damage that 
may have occurred during transit. Please check it against the photograph on carton. If any parts are missing, please contact our Consumer
Helpline:
Phone: 1-800-423-3598
E-Mail: info@alltradetools.com

DO NOT OPERATE THIS AIR COMPRESSOR IF DAMAGED DURING SHIPMENT, HANDLING OR MISUSE. 

DAMAGE MAY RESULT IN BURSTING, WHICH CAN CAUSE SERIOUS INJURY OR PROPERTY DAMAGE. 

ALL DAMAGED PARTS MUST BE REPAIRED OR REPLACED AS NEEDED PRIOR TO OPERATING THIS AIR COMPRESSOR.

Check to see that all nuts, bolts and fittings are secure before putting this air compressor into service. If you have any questions, or require
assistance with damaged or missing parts, please contact our Consumer Helpline:
Phone: 1-800-423-3598
E-Mail: info@alltradetools.com

Please have the serial number, model number, date of purchase, and parts list (with missing parts identified) available for reference when
calling.

MODEL NUMBER:  _______________________________________

SERIAL NUMBER:   _______________________________________

DATE of PURCHASE:   _____________________________________

2

DANGER

Summary of Contents for 835534






















Reviews: