ALPATEC taurus MG 15 DIGITAL, Manual

bags, polystyrene or cables within the reach of 

children.

- During transportation, the tilt angle of the 

appliance must not exceed 45 °. Do not locate 

the appliance upside down as this may damage 

the compressor.

- Do not remove the appliance’s support legs
- Place the appliance on a flat, stable surface and 

away from any heat source.

- The appliance requires proper ventilation in 

order to operate correctly. Leave a free space of 

15 cm around the appliance.

- Do not obstruct the opening of the door of the 

appliance.

- The socket should be easily accessible in order 

to be able to quickly disconnect the appliance in 

case of an emergency.

INSTRUCTIONS FOR USE

BEFORE USE:

- Make sure that all products’ packaging has been 

removed.

- Before using the product for the first time, clean 

the parts that will come into contact with food in 

the manner described in the cleaning section.

- It is recommended that you wait for a minimum 

of 2 hours after having installed the appliance 

before you use it for the first time, leaving the 

front cover open.

- Prepare the appliance according to the function 

you wish to use:

FILLING WITH WATER:

- You must fill the water compartment before 

turning on the appliance.

- Extract the receptacle from its place.
- Fill the compartment with cold water.
- Fill the receptacle taking care to observe the 

MAX and MIN level. 

- Put the container back onto its place.

USE:

- Ensure that the electronic connector is properly 

attached to the appliance.

- Fill the appliance with water observing the maxi-

mum level. Do not place any liquid other than 

drinking water in the tank.

- Connect the appliance to the mains.
- Turn the appliance on, by using the on/off switch 

(G).

- Turn the appliance on, by using the on button (1).
- The processing time is approximately 7-12 

minutes (depending on water temperature and 

room temperature). Caution: The ice cubes 

produced may be small and irregular during the 

first 3 cycles.

- Once the ice cubes have been processed, the 

excess water will drain into the water tank and 

the cubes will fall onto the ice tray (B).

- Caution: the cubes may not be fully transpa-

rent, due to the air entering during processing 

development but this does not alter the quality 

of the cubes.

- When the water tank is empty, the «Tank emp-

ty» light (4) will light up in white and a beep will 

sound for a few seconds.

- Turn off the appliance.
- Fill tank while observing the maximum level.
- Wait 3 minutes before running the appliance again.
-  When the ice cube tray is full, the «Tray full» 

light (3) will light up and several beeps will 

sound.

- Drain the ice cube tray with the help of the 

spoon supplied with the appliance.

- Never leave the ice tray full while the appliance 

is in use.

- To completely empty the water tank, open the 

drain plug (E) located inside the tank, ensuring 

that there is a container underneath the applian-

ce. Once the tank is emptied, replace the plug 

(E) in the tank.

SETTING THE TIME

- Press the Time button (6) to set the device time
- Press Press to reach the desired time
- Press the Time button to set the minutes of thE 

device

- Press SET to reach the desired minutes

TIMER FUNCTION

- Press the timer function button to set the on / off 

time as desired.

ONCE YOU HAVE FINISHED USING THE 

APPLIANCE:

- After use, press the stop button to turn off the 

appliance.

- Turn the appliance off, using the on/off switch.
- Unplug the appliance from the mains.
- Remove the water from the inside of the appliance.
- Drain and dry the water tank before storing the 

appliance if you are not going to use it for an 

extended period of time.

- Clean the appliance.