background image

2.2 General Requirements 

2.2.1 IEEE 802.11b Section 

Feature 

Detailed Description 

2.2.1.1 

Standard 

Ÿ 

IEEE 802.11b 

2.2.1.2 

Radio and 
Modulation 
Schemes 

Ÿ 

DQPSK, DBPSK, DSSS, and CCK 

2.2.1.3 

Operating 
Frequency 

Ÿ 

2400 ~ 2497MHz ISM band 

2.2.1.4 

Channel 
Numbers   

Ÿ 

11 channels for United States 
13 channels for Europe Countries 
14 channels for Japan 

2.2.1.5 

Data Rate 

Ÿ 

11, 5.5, 2, and 1Mbps 

2.2.1.6 

Media Access 
Protocol 

Ÿ 

CSMA/CA with ACK 

2.2.1.7 

Transmitter 
Output Power 

Ÿ 

Typical 18dBm at 11, 5.5, 2, and 1Mbps 

2.2.1.8 

Receiver 
Sensitivity 

Ÿ 

Typical 

84dBm for 11Mbps @ 8% PER 

Ÿ 

Typical 

90dBm for 2Mbps @ 8% PER 

2.2.2 IEEE 802.11g Section 

Feature 

Detailed Description 

2.2.2.1 

Standard 

Ÿ 

IEEE 802.11g 

2.2.2.2 

Radio and 
Modulation 
Schemes 

Ÿ 

BPSK, QPSK, 16QAM, 64QAM, and OFDM 

2.2.2.3 

Operating 
Frequency 

Ÿ 

2400 ~ 2497MHz ISM band 

2.2.2.4 

Channel Numbers   

Ÿ 

11 channels for United States 
13 channels for Europe Countries 
13 channels for Japan 

2.2.2.5 

Data Rate 

Ÿ 

54, 48, 36, 24, 18, 12, 9, and 6Mbps 

Ÿ 

108Mbps for USA only 

2.2.2.6 

Media Access 
Protocol 

Ÿ 

CSMA/CA with ACK 

2.2.2.7 

Transmitter 
Output Power 

Ÿ 

Typical RF Output Power at each Data Rate 

Ÿ 

+10 ~ 14dBm at 54Mbps 

Ÿ 

+11 ~ 15dBm at 48Mbps 

Ÿ 

+13 ~ 15dBm at 36Mbps 

Ÿ 

+17 ~ 18dBm at 24, 18, 12, 9, and 6Mbps 

2.2.2.8 

Receiver 

Ÿ 

Typical Sensitivity at Which Frame (1000-byte 

Summary of Contents for WMP-G07















Reviews: