background image

2. Warning before use: 
Make sure you read the instructions manual 

Once you remove the packaging, you need to inspect whether the furnace is complete in terms of 

 

the basic elements, and whether the fire-resistant glass on the front side is in good condition. 
 

3.

 

Description of the Furnace 

 

    The furnace is designed to allow efficient combustion of solid fuel with the option to adjust and regulate 
the necessary amount of air for the combustion process. 
    When it comes to construction, the furnace is different compared to other solid fuel furnaces in terms of 
both  its  design  and  the  composition  of  certain  elements.  It  is  made  out  of  sheet  metal  and  cast,  which 
make it very easy to maintain and clean. The outer shell is enamelled or painted. 
    The combustion chamber is made of sheet metal, and it is coated with cast positions on the inside. On 
the  front  side  of  the  furnace,  there  is  a  fire  resistant  glass  with  mirror  effect.  You  can  see  the  flame 
through  the  middle  glass, which  produces  a  special  effect  while  heating  up  the  room.  Also, there  is  the 
combustion door  on the right side of  the  furnace,  which  when left open  in turn opens the lateral  middle 
right side of the furnace.  Lateral middle  right side  is  connected to the chamber with a hinge and a right 
batten. The closed lateral middle right side is connected to the chamber with a magnet. 
    Opening and closing of the lateral right side combustion door is done using a special wrench, by lifting 
the handle and placing the wrench cogwheel into the handle opening. 
    In the middle part of the furnace, there are two pieces of glass with fireproof interior and exterior areas, 
and decorative mirror effect. The inner glass is on the front door of the furnace that is not being used. 
When replacing the inner glass in a special case, when cleaning the inner glass or when removing the 
residue, you should remove the burner, cap, lateral left and right sides, upper glass with the mirror effect 
and the middle glass with the mirror effect (Figure 1). We have reached the front door, which can be 
opened and leaned against the front of the furnace, and we can replace the glass, clean the soot from the 
glass, and if needed, remove the residue.                                                                                                                             
 
    Under the ash tray cover (Figure 1, position 1), there are two air controllers for regulation of required 
amount of combustion air. 
 

 

                            Fig. 2 
    The ash  tray is  bolted  with an  interlock  and can  be pulled  out using  a  special wrench (see Fig. 2) by 
placing the prism top into the ash tray holder.  
    At the back side of the furnace, there is a chimney plug with a throttle shaft and a throttle that regulates 
the  airflow.  The  throttle  position  is  fixed  to  the  shaft  using  a  spring,  thus  retaining  the  airflow.  The 
maximum  airflow  in  the  furnace  is  achieved  when  the  throttle  shaft  is  in  a  horizontal  position,  while  the 
minimum airflow is achieved when the throttle shaft is in a vertical position. The necessary airflow in the 
chimney is 10 Pa (1 mm VS) at minimum. 
 
 
 
 
 
 
 

Summary of Contents for ALPHA FURNACE 2014










Reviews: