background image

Safety Notes

Review the drawings and illustrations contained in this manual before proceeding. If there are any questions 

regarding the safe installation or operation of the system, contact Alpha Technologies or the nearest Alpha 

representative. Save this document for future reference.
To reduce the risk of injury or death and to ensure the continued safe operation of this product, the following 

symbols have been placed throughout this manual. Where these symbols appear, use extra care and 

attention.

There may be multiple warnings associated with the call out. Example:

ELECTRICAL HAZARD WARNING provides electrical safety information to 

PREVENT INJURY OR DEATH to the technician or user.

WARNING! ELECTRICAL HAZARD

WARNING! FUMES HAZARD

FIRE HAZARD WARNING provides flammability safety information to PREVENT 

INJURY OR DEATH to the technician or user.

WARNING! FIRE HAZARD

WARNING! FIRE & ELECTRICAL HAZARD

ATTENTION:

 

The following sections contain important safety information that must be followed during the installation and 

maintenance of the equipment and batteries. Read all of the instructions before installing or operating the 

equipment. Save this manual for future reference.

ATTENTION provides specific regulatory/code requirements that may affect the placement of equipment and/

or installation procedures.

NOTICE:

NOTICE

 provides additional information to help complete a specific task or procedure.

CAUTION! 

CAUTION provides safety information intended to PREVENT DAMAGE to material or 

equipment.

This WARNING provides safety information for both Electrical AND Fire Hazards

FUMES HAZARD WARNING provides fumes safety information to PREVENT 

INJURY OR DEATH to the technician or user.

Summary of Contents for FP1208-F-5A





















Reviews: