background image

 

 PD9B01M0 1ST ISSUE 1/07/2019                                                                                        27 

9.5  Flap computer (if installed) 

The flaps are simultaneously actuated by an electromechanical actuator and controlled electrically 
by the pilot through a special single switch (flap computer) located on the instrument panel. Power 
entering to  the flap  actuators  is  protected  by  a  breaker.  The flap  computer  allows the  flaps  to  be 
deployed in steps at pre-configured values. The flap computer is pre-set by the company.  In case 
reset is necessary, consult the OEM User Manual.  Additional information is included in the in the 
ANNEX A (Electrical & Avionics group) in order to manage this operation. 

9.6  External power source (for engine startup) 

Plug  the  Alpi  Aviation  standard  connector  (supplied  in  bundle  with  the  aircraft)  into  the  cowl  port 
side.  Be  sure that  the  red  wire  connects  with  the  positive  and  black  one with  the  negative  in the 
external power unit.  Start as for normal operation. Be careful about the propeller  when removing 
the  external  plug.  Additional  information  is  included  in  the  in the  ANNEX  A  (Electrical  &  Avionics 
group) in order to manage this operation. 

 

CAUTION 

WHEELS  MUST  BE  CHOCKED.  BRAKES  MUST  BE  ON.  FACE  AIRCRAFT  INTO  WIND. 
ENSURE PROPEL

LER IS CLEAR. ENSURE QUALIFIED PERSON IS IN THE PILOT’S SEAT. 

 

10 Structural repair 

10.1  Type of maintenance 

According to  ASTM  F2483-12  definition,  already  recalled  in  para.  1.1,  the  maintenance, repair  or 
alteration prescribed for this operations are defined 

Heavy

10.2  Minimum level of certification 

-  Repairman, Light Sport Aircraft-Maintenance (RLSA-M) or higher; 
-  For composite and wood components Alpi Aviation task specific training is required; 
-  Authorized Alpi Aviation Service Centres are equipped to perform this type of repairs. 

10.3  Repair procedures 

No structural repairs are authorized without further consultation with the manufacturer. 
 
Structural  repairs  on  composites  or  wood  parts  of  this  aircraft  cannot  be  defined  by  standard 
procedures.  The  combination  of  materials  on  this  aircraft  is  in  some  areas  unique.  Therefore,  in 
any case, the individual repair procedure has to be agreed with the airframe manufacturer upfront. 
Approval  of  the  manufacturer  is  also  necessary  to  ensure  compliance  with  applicable  standards 
and regulations. 

10.4  Materials necessary for small repairs 

The  minimum  set  of  materials  to  accomplish  small  repairs  are  herein  listed.  For  further  details 
contact the facility, see A.2 Original Equipment Manufacturer. 

o

 

Filler (suitable for wood, steel, aluminum and plywood); 

o

 

Fabric Glue; 

o

 

Fabric primer; 

o

 

Epoxy resin (with catalyzer); 

Summary of Contents for PIONEER 300








































Reviews: