background image

7

For more information about our company or products, please visit our website at www.alpine4u.com or call us (USA) 1-877-710-0162

Starting up Pumps Installed in Water (See Figure 4.1 on page 6) 

Important Note:

 Do not run the pump dry as this can cause damage.

A.  Place the pump in the water and let it fill with water

B.  To prevent unnecessary soiling, install the pump on a solid

         stone tile to ensure that it does not stand in sludge and suck

         it in.

C.  Ensure that there is at least 4 inches of water above the pump

         so that the pump cannot suck in air.

D.  The pump should not be immersed to a depth exceeding 13 feet

         under water. 

E.  Turn the pump casing in the desired position and install the

         accessories on the threaded connection of the pump.

F.  Plug your pump into your local power supply and on select   

         models you can control the flow rate from the controller.

 

          See figure 4.2  

Starting Pumps with Dry Installation (See Figure 4.1 on page 6)

The pump can also be installed outside the water.

A.  Remove the Pre-filter cage from the pump.

B.  Place the pump below the water level next to the pond, so 

        that the water can flow into the pump (this pump is not 

        self-priming).

C.  Turn the pump to the desired position and install a suction 

         hose and output hose to the pump, to ensure air and

         water-tightness. 

See figure 4.3

D.  The suction hose must be completely filled with water before 

         starting operation.

E.     Start the pump by plugging your pump into your local power 

        supply and on select models you can control the flow rate 

        from the controller. 

F.  Tip: To protect the pump from soiling, the suction side must 

         be provided with a pre-filter.

Removal and Storage of Waste

Electrical home appliances should be disposed of according to US standards. The product should not be disposed of with 

normal household waste but should be collected separately. You are responsible to ensure that the appliance is returned to a 

specially designated collection point, to be dismantled and you’re processed in an environmentally friendly manner.

For more information on local waste collection points, please contact the municipality under which your residence is

covered.

(Figure 4.2)

(Figure 4.3)

Max. 13ft

Summary of Contents for eco-SPHERE PUR1400












Reviews: