33
-EN
01GB04INE-W960E.fm
ALPINE INE-W960A/INE-W960E INE-W960E_OM (EN)
Adjusting the Crossover Settings (X-
Over)
[X-Over]
is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 29).
Before performing the following procedures, refer to “About the
Crossover” (page 36).
Setting item: X-Over
1
Touch
[Channel]
to select the channel.
Each time you touch, the channel switches.
•
The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[
]
or
[
]
of “Freq.”, then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch
[
]
or
[
]
of “Slope”, then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct
Adjusting the Level
Touch
[
]
or
[
]
of “Level”, then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
4
To store the adjusted setting value, touch and hold
[Preset1]
,
[Preset2]
, or
[Preset3]
for at least 2
seconds.
•
Touch
[Flat]
to initialise all values.
•
If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
be edited (Refer to page 34).
•
If the Subwoofer setting is “Off,” the Subwoofer setting cannot be
edited (Refer to page 34).
•
While adjusting the X-Over you should consider the frequency
response of the connected speakers.
Calling the X-Over adjusted value
Calling the pre-set X-Over adjusted value.
Touch
[Preset1]
,
[Preset2]
, or
[Preset3]
on the X-
Over screen.
The setting stored in the Preset will be recalled.
Adjusting the Parametric Equalizer
Curve (Parametric EQ)
[Parametric EQ]
is selected on the Sound setup menu in step 3. Refer
to “Sound Setup Operation” (page 29).
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
Setting item: Parametric EQ
1
Adjust the Parametric EQ to your preference.
Adjusting the Band
Touch
[Band]
to select the band to be adjusted.
•
You can select a band directly by touching the screen.
Adjusting the Frequency
Touch
[
]
or
[
]
of “Freq.” to adjust the frequency of the
selected band.
Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps)
Front HPF
Rear HPF
SubW. LPF
Band1
Band2
···
Band8
Band9
Band1:
20 Hz~100 Hz (63 Hz)
Band2:
63 Hz~315 Hz (125 Hz)
Band3:
125 Hz~500Hz (250 Hz)
Band4:
250 Hz~1 kHz (500Hz)
Band5:
500 Hz~2 kHz (1 kHz)
Band6:
1 kHz~4 kHz (2 kHz)
Band7:
2 kHz~7.2 kHz (4 kHz)
Band8:
5.8 kHz~12 kHz (8 kHz)
Band9:
9 kHz~20 kHz (16 kHz)
01GB00INE-W960E.book Page 33 Wednesday, November 19, 2014 5:31 PM
