28
-EN
Setting the A.Processor
1
Check that Defeat mode is off (page 14).
2
Press and hold
SETUP
for at least 2 seconds.
The SETUP selection screen is displayed.
3
Touch
[
]
of Audio Setup.
The AUDIO SETUP screen appears.
•
The AUDIO SETUP screen can also be activated directly by pressing
SOUND/IMPRINT
.
4
Touch
[
]
of A.Processor.
The A.PROCESSOR list screen appears.
5
Touch
[
]
,
[
]
or
[
]
etc., of the desired item to
change its setting.
Setting items:
Media Xpander / Bass Sound Cont. / DOLBY PLII / REAR FILL /
X-Over / T.Corr / Phase / G-EQ / P-EQ / Speaker Select /
Multi CH Setup / Speaker Setup / DVD Level / PCM Mode
•
Touching
[
]
to return to the previous screen.
•
Touch and hold
[
]
for at least 2 seconds to return to the main
source screen that was displayed before the setup operation was
started.
Before performing the operations below, set MX (Media Xpander)
mode of the PXA-H700 to “AUTO” when the PXA-H700 is connected.
Setting item: Media Xpander
1
Select ON or OFF of MX by touching
[
]
or
[
]
of
Media Xpander.
2
Touch
[
]
after setting to ON.
The Media Xpander setup screen appears.
3
Touch
[
]
or
[
]
of the desired MX mode.
•
Music source (such as radio broadcasts and CDs, excluding MW, LW
radio) level can be set.
MX CD (OFF, CD MX 1 to 3)
CD mode processes a large quantity of data. This data is used
to reproduce the sound cleanly by making use of the data
quantity.
MX CMPM (OFF, CMPM MX 1 to 3)
This corrects information that was omitted at the time of
compression. This reproduces a well-balanced sound close to
the original.
MX FM (OFF, FM MX 1 to 3)
The medium to high frequencies become more clear, and
produces well balanced sound in all the bands.
MX DVD (OFF, MOVIE MX 1 to 2)
The dialog portion of the video is reproduced more clearly.
MX AUX (OFF, CMPM MX, MOVIE MX, MUSIC MX)
Choose the MX mode (CMPM, MUSIC, or MOVIE) that
corresponds to the media connected.
•
The contents of MX set here are reflected to PXA-H700 or
PXA-H701.
•
When OFF is selected, MX effect of each MX mode will be OFF.
•
Each music source, such as radio, CD and MP3 can have its own MX
setting.
•
MX mode does not function when MX is ON for MW, LW radio.
•
MX CMPM is applied for MP3/WMA/AAC and iPhone/iPod.
•
The MX setting can be performed only when a source is currently
selected.
Setting item: Bass Sound Cont.
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
Touch
[
]
or
[
]
of Bass Comp. to select the desired
mode.
Bass sound is emphasised more as the mode is
sequentially switched as MODE 1
2
3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
Setting Bass Focus
Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
Set the delay number in the front and rear, and on the
right and left of the desired speaker by touching the
respective
[
]
or
[
]
button.
•
Any setting in Bass Focus is applied in time correction, too (page 29).
Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a “REAR
FILL” function for outputting the signals of the front channel to the rear
channel.
Setting item: DOLBY PLII/REAR FILL
Touch
[
]
or
[
]
of DOLBY PLII/REAR FILL to select the
desired mode.
Setting the MX Mode of External Audio
Processor
OFF:
Turns off the MX effect of every music source.
ON:
Turns on the specified MX mode.
(DVD MUSIC)
This disc contains a large quantity of data such as music clip.
MX uses this data to reproduce the sound accurately.
Setting Bass Sound Control
Using the Pro Logic II Mode
PL II MOVIE:
Applicable for all stereo video programming. It
also works well with programmes encoded with
Dolby Surround. The processed sound-field
approaches that of discrete 5.1 channel sound.
PL II MUSIC:
Can be used for all stereo music recordings, and
provides a wide, deep sound field.
OFF:
Turns DOLBY PL II function to OFF.
