background image

 

 

11 

the IP address of the b@home gate. 
 
 
 
 
 
 
 

 

If you are not able to establish a connection to the b@home gate, check the network connection and the settings 
of your router (also see Section 6. System requirements). 

 

14.1.2 b@home app 

The b@home app is available for free from the App Store (iOS 7.0 or higher) or Google Play Store 
(Android 2.2 or higher). 

 

 
 
 
 
 
 
 
 
 

For security reasons, the mobile end device has to be authenticated. This is a one-off process (see on-screen 
instructions).  

 

If you are not able to establish a connection to the b@home gate, check your network connection and/or the settings 
of your router (also see Section 6. System requirements). 
 
 

14.1.3 b@home portal 

Once you have set up Internet access via the b@home gate’s configuration interface (see 14.9), 
you can go to https://www.klimaregler.de on the b@home portal to undertake settings on your 
system. 

 
 

14.2 Name in network (host name) 

If you are using just one b@home gate in your network, no changes are needed. 

 
If further b@home gates are to be operated in the same network, before starting up another b@home gate, you need to 
change the destination address http://bathomegate/  (e.g. into http://bathomegate1/) because the same destination 
addresses are not permitted in a network.  
 
 
 
 

14.3 System functions 

State the functions your temperature control system can perform: 

 

heating 

 

cooling   

 

heating and cooling 

 
 These settings depend on the type of temperature control system and the actuators (receivers) used. An incorrect 

selection may result in damage to the system and increased energy consumption. 

 
 
 

14.4 Designation of the b@home gate 

Any name can be entered and is displayed in the b@home app and b@home portal.  
 

IP address (example): 
 
http://192.168.0.100 

App 

Portal 

Gate 

 

 

Gate 

 

App 

 

Portal 

 

Gate 

 

App 

 

Summary of Contents for B@home System


























Reviews: