background image

 

 

15 

14.6.4 Training actuator (wireless room temperature controller/receiver) 

At least one actuator should be trained for each room. Once you have pressed the “Train actuator” button, the training 
function must be triggered on the actuator within 15 seconds. To do this, briefly press the training button once. If using 
multi-channel actuators, the corresponding channel must first be selected with the channel selection button. Any 
combinations and quantities of actuators can be trained per room. 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
More information about training actuators can be found in the respective actuator operating instructions. 
 
Trained sensors are displayed in the b@home app, b@home portal or on the user interface (HTML page) of the 
b@home gate - while actuators are not.  
 
Possible manual settings on actuators, such as central control or exclusion of channels from cooling mode, must 
be reset to the factory settings before training.  

 
 
 
 

14.6.5 Cancelling actuator (wireless room temperature controller/receiver) 

To cancel, press and hold the actuator’s training button until the lamp lights up red permanently after around 10 seconds. 
The lamp of the deleted channel lights up red permanently to indicate that the entire receive channel has been successfully 
deleted. Control is now deactivated. 
 

If using multi-channel actuators, the corresponding channel must first be selected with the channel selection button. 

 

More information about cancelling actuators (deleting entire receive channel) can be found in the respective 
actuator operating instructions. 

 
 
 

14.6.6 Connection test 

Pressing the “Connection test” button allows the correct wireless connection between b@home gate and actuators to be 
tested. If the connection is correct, the lamp on the actuator/channel briefly lights up green and then lights up green for a 
further approx. 15 seconds.  

Gate 

 

App 

 

Training button / channel 
selection button of 
multi-channel actuators  
HTFRx-214.140 
HTFRx-316.125 
KTFRx-213.140 
KTFRx-315.125 

Training button on  
HTFRB-010.101 
actuator 

Training button on  
HTFRA-010.101 
actuator 

Training button on 
HTFRU-010.101 
actuator 

Training button on 
HTFRU-010.124 
actuator 

Training button on 
HTFMA-180.161 
actuator 

Summary of Contents for B@home System


























Reviews: