background image

 

 

16 

 

The description of the connection test in the operating instructions for the sensors and actuators may differ from 
this.  
 
The HTFMA-180.161 actuator does not support the connection test. 

 
 
 
 

14.6.7 Deleting room 

You can use this function to remove the room from the list of rooms. This deletes all settings and trained sensors. 
 

Actuators, which were not cancelled before the room was deleted, switch to emergency mode. More information 
about emergency mode and cancelling can be found in the respective actuator operating instructions. 

 
 
 
 

14.7 Automatic program 

The switching times can be set in 15-minute intervals and setpoint temperatures programmed for this room. The switching 
times can be transferred to other days of the week. 
 
 
 
 

14.8 Central functions 

These functions affect all rooms. Operating modes can thereby be quickly changed for the entire system, functions such as 
party or holiday can be quickly activated or system settings quickly undertaken.

 

 
 
 

 

14.9 Setting up Internet access 

In order to operate the b@home system outside your home network, you need to create a new user account or assign an 
existing account to your b@home gate. To do this, open the configuration interface of the b@home gate (see Section 
14.1.1). 
Once a user account has been set up/assigned, the b@home system can be controlled and monitored from any location 
using the b@home app or b@home portal by going to https://www.klimaregler.de. 
 
When establishing the connection to the b@home portal, the system time set of the b@home gate is used to determine the 
time zone for automatic time corrections. Ensure that the correct time has been set in the b@home gate (see Section 14.5) 
before taking this step. 
 
 
 
 

14.10 Factory settings 

This function either partially or completely resets user settings. Follow the corresponding on-screen instructions. 
 
 
 
 

14.11 Firmware update 

Here  you can view the installed firmware version of the b@home gate and look for updates. We always recommend 
installing the most recent version. While an update is taking place, the two lamps on the b@home gate flash blue. If 
necessary, once the update is complete, you can return to the previous firmware version. 
 

While an update is taking place, do not disconnect the power supply or Internet connection to your b@home gate 
because under certain circumstances, this may damage the system. 

 

 
 

Gate 

 

Gate 

 

App 

 

 

Gate 

 

Gate 

 

App 

 

 

Portal 

 

App 

 

Gate 

 

App 

 

Portal 

 

App 

 

Summary of Contents for B@home System


























Reviews: