background image

 

 

22 

16.9 Installation tips 

The following tips should be noted when installing the wireless components: 
 

 The transmission path should be as short as possible 

 The number of times the wireless signal passes through ceilings and walls should be reduced as much as possible 

 The angle of incidence through the wall or ceiling also affects the signal attenuation 

 
 

                                                                            

Floor plan showing signal passing through 3 walls and/or doors

 

 
 
The central component of the b@home gate should be positioned 

centrally

 in the building to avoid large distances and 

to reduce the number of times that walls and ceilings have to be passed through. 
 
Furthermore, the transmitter and receiver should 

not

 be fitted on the same wall side. We would recommend installing 

them on opposite walls. 
 

 

                                      

Floor plan showing short transmission paths and passing through a small number of walls 

 
 
 

Receiver

 

Transmitter

 

Transmitter 

Receiver 

Timer sensor or 

b@home gate 

Transmitter 1 

Transmitter 2 

Summary of Contents for B@home System


























Reviews: