manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual

The Altera Stratix V Hard IP user manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on effectively utilizing the product's features and functionalities. Enhance your understanding and optimize your experience with our cutting-edge technology by referring to the user manual available at 88.208.23.73:8080.

Share
Download
background image

Chapter 5: IP Core Architecture

5–11

PCI Express Avalon-MM Bridge

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

■

LTSSM—This block implements the LTSSM and logic that tracks what is received 
and transmitted on each lane. 

■

For transmission, it interacts with each MAC lane sub-block and with the 
LTSTX sub-block by asserting both global and per-lane control bits to generate 
specific Physical Layer packets. 

■

On the receive path, it receives the Physical Layer Packets reported by each 
MAC lane sub-block. It also enables the multilane deskew block. This block 
reports the Physical Layer status to higher layers.

■

LTSTX (Ordered Set and SKP Generation)—This sub-block generates the Physical 
Layer Packet. It receives control signals from the LTSSM block and generates 
Physical Layer Packet for each lane. It generates the same Physical Layer Packet 
for all lanes and PAD symbols for the link or lane number in the corresponding 
TS1/TS2 fields. 

The block also handles the receiver detection operation to the PCS sub-layer by 
asserting predefined PIPE signals and waiting for the result. It also generates a 
SKIP ordered set at every predefined timeslot and interacts with the TX alignment 
block to prevent the insertion of a SKIP ordered set in the middle of packet.

■

Deskew—This sub-block performs the multilane deskew function and the RX 
alignment between the number of initialized lanes and the 64-bit data path. 

The multilane deskew implements an eight-word FIFO for each lane to store 
symbols. Each symbol includes eight data bits, one disparity bit, and one control 
bit. The FIFO discards the FTS, COM, and SKP symbols and replaces PAD and 
IDL with D0.0 data. When all eight FIFOs contain data, a read can occur. 

When the multilane lane deskew block is first enabled, each FIFO begins writing 
after the first COM is detected. If all lanes have not detected a COM symbol after 
seven clock cycles, they are reset and the resynchronization process restarts, or 
else the RX alignment function recreates a 64-bit data word which is sent to the 
DLL.

PCI Express Avalon-MM Bridge

In Qsys, the Stratix V Hard IP for PCI Express is available with either an Avalon-ST or 
an Avalon-MM interface to the Application Layer. When you select the Avalon-MM 
Stratix V Hard IP for PCI Express, an Avalon-MM bridge module connects the PCI 
Express link to the interconnect fabric. The bridge facilitates the design of Endpoints 
that include Qsys components. 

The full-featured Avalon-MM bridge provides three possible Avalon-MM ports: a 
bursting master, an optional bursting slave, and an optional non-bursting slave. The 
Avalon-MM bridge comprises the following three modules:

■

TX Slave Module—This optional 64- or 128-bit bursting, Avalon-MM dynamic 
addressing slave port propagates read and write requests of up to 4 KBytes in size 
from the interconnect fabric to the PCI Express link. The bridge translates requests 
from the interconnect fabric to PCI Express request packets.

■

RX Master Module—This 64- or 128-bit bursting Avalon-MM master port 
propagates PCI Express requests, converting them to bursting read or write 
requests to the interconnect fabric.

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments

Related manuals for Stratix V Hard IP

IEI Technology KINO-DQM871 User Manual preview
KINO-DQM871
Brand: IEI Technology Pages: 211
IEI Technology IOWA-MARK Quick Installation Manual preview
IOWA-MARK
Brand: IEI Technology Pages: 8
IEI Technology KINO-G45A Quick Installation Manual preview
KINO-G45A
Brand: IEI Technology Pages: 8
JETWAY NF9U-F Technical Manual preview
NF9U-F
Brand: JETWAY Pages: 52
Gigabyte GA-E3000N User Manual preview
GA-E3000N
Brand: Gigabyte Pages: 31
IEI Technology IMBA-G412ISA-R20 User Manual preview
IMBA-G412ISA-R20
Brand: IEI Technology Pages: 164
Xilinx ML505 Getting Started Tutorial preview
ML505
Brand: Xilinx Pages: 31
Texas Instruments TPS54231 User Manual preview
TPS54231
Brand: Texas Instruments Pages: 21
Gigabyte GA-EP43T-USB3 User Manual preview
GA-EP43T-USB3
Brand: Gigabyte Pages: 96
ON Semiconductor NCV891234 User Manual preview
NCV891234
Brand: ON Semiconductor Pages: 8
JETWAY NF9A-Q67 Technical Manual preview
NF9A-Q67
Brand: JETWAY Pages: 41
QDI P5I915PL Manual preview
P5I915PL
Brand: QDI Pages: 47
TYAN S7105 Manual preview
S7105
Brand: TYAN Pages: 164
IEI Technology IMBA-C604EN User Manual preview
IMBA-C604EN
Brand: IEI Technology Pages: 198
ASROCK P45X3 DELUXE - Installation Manual preview
P45X3 DELUXE -
Brand: ASROCK Pages: 212
Erreka IRPROGM Quick Programming Manual preview
IRPROGM
Brand: Erreka Pages: 4
Micrel MIC23031-4YMT EV Getting Started preview
MIC23031-4YMT EV
Brand: Micrel Pages: 8
Supero X9DRT-HF+ User Manual preview
X9DRT-HF+
Brand: Supero Pages: 105

Brands by name

Popular brands

Load more brands