Altigen AltiWare ACC 5.2 Administration Manual Download

Page: 337 / 399

Chapter 25: Enterprise VoIP Network Management

AltiWare ACC 5.2 Administration Manual 325

Changing an Extension’s Scope from Global to Local

If you want to change an extension's scope from Global to Local, you can highlight the
extension and click the

Change All Global to Local

button. This extension's scope in

other member systems will be impacted after Global is changed to Local. Using the

previous case as an example, you may encounter one of the following situations when
changing an extension's scope from Global to Local.

Situation 1: One Global and no conflict

Before you make the change, extension 100’s scope is as follows:

After you change extension 100 to Local, the scope of 100 will be:

Note:

After you make the change, users in Systems B and C cannot dial and ring
extension 100. Only System A users can call local extension 100.

Situation 2: One or more Global with conflict

Before you make the change, the scope of extensions 403 and 404 is as follows:

After you change the two extensions to Local, their scope will be:

Ext.

System A

System B

System C

100

Global

Remote

Ext.

System A

System B

System C

100

Local

Not Found

Ext.

System A

System B

System C

403

Global

Local

404

Global

Local

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Search results

Summary of Contents for AltiWare ACC 5.2

Reviews:

Related manuals for AltiWare ACC 5.2

Brands by name

Popular brands

Altigen AltiWare ACC 5.2, Administration Manual

Search results

Summary of Contents for AltiWare ACC 5.2

Reviews:

Related manuals for AltiWare ACC 5.2

Brands by name

Popular brands