Altigen AltiWare OE 4.6 Administration Manual Download | Manualshive

Page: 308 / 518

background image

Setting Dialing Pattern Routing

9-8

AltiWare OE System Installation & Administration Manual

Example: 10-Digit Dialing

A sample use of dialing patterns is enabling 10-digit dialing, which some
geographical areas require. Normally, AltiServ prepends a “1” to 10-digit
numbers when users use single-click calling features such as zoomerang or
calling from a Contacts list in AltiView or a TAPI-enabled application.
This could cause some calls to fail. Here is how you would enable 10-digit
dialing.

1.

On the Route Definition tab, define a route that deletes one digit from
the head.

2.

On the Dialing Pattern tab, create a dialing pattern with Prefix set to
<1+area code>, such as “1408,” and Pattern length set to “11,” where
area code is different from the AltiServ system but requires 10-digit
dialing.

3.

Assign the Route Priority for this dialing pattern to the Index of the
route definition you created above.

4.

Repeat steps 2 and 3 above for other area codes requiring 10-digit
dialing as necessary.

Reducing Dialing Delay For En-Bloc Trunks For Non-US/
Canada Countries

When using a country code other than USA & Canada in System
Configuration, there will be a 7 second dialing delay for en-bloc trunks. To
reduce this delay, Out Call Routing Configuration can be used as a
workaround.

To reduce dialing delay:

1.

In the Number Plan page of System Configuration, select a digit for
route access.

2.

In the Route Definition page of Out Call Routing Configuration,
add a route definition entry for en-bloc and assign the member en-bloc
trunk(s).

«
...
306
307
308
309
310
...
»

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare OE 4.6

PowerShot SX1 IS

Brand: Canon Pages: 48

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Pixma Pro9500 Series

Brand: Canon Pages: 31

PowerShot SD430 DIGITAL ELPH WIRELESS

Brand: Canon Pages: 130

PowerShot SD880 IS Digital ELPH

Brand: Canon Pages: 83

Brand: Canon Pages: 34

N1240U - CanoScan Flatbed Scanner

Brand: Canon Pages: 109

Brand: 3M Pages: 3

NG Network Access Client SP4

Brand: Barracuda Networks Pages: 268

TRANSCEND EM/NT 6.3

Brand: 3Com Pages: 39

DRAGON NATURALLYSPEAKING PROFESSIONAL 5

Brand: Dragon Systems Pages: 222

Brand: Allied Telesis Pages: 46

NeatWorks For Mac

Brand: NeatWorks Pages: 33

Brand: HP Pages: 15

Surestore 5200ex - Optical Disk Drives

Brand: HP Pages: 77

Brand: HP Pages: 778

Brand: Palm Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands