background image

                                                                   V-MATRIX

3

ABOUT YOUR V-MATRIX™ VIDEO/SYNC
OUTPUT

 

CARDS

2

VM2144VS/VM2145SS/VM2146UX

8-out V-MATRIX™ Video/Sync Output Cards

The 

VM2144VS/VM2145SS/VM2146UX

 are 8-

output Cards designed for use in a V-Matrix™
enclosure and can handle a wide array of signal
formats and connector types. When installed in a
V-Matrix™ Basic Enclosure, these Output cards
enable the connection of eight composite sources
when used with the 

VM2143VS

 8-in Video/Sync

Input Card. 

See the VM2143VS for more

information.

The 

VM2144VS/VM2145SS

 8-output video/sync

cards provide built-in ground loop isolation (GLI on
Board™) through the use of differential inputs. This
is an extremely important feature because it
protects against hum bars and other interference
caused by ground loops, which notoriously wreak
havoc on large-scale matrix systems. Both the
input and output video cards provide a bandwidth
of 350 MHz @ –3dB, allowing them to pass
extremely high-resolution computer video/sync
signals without signal degradation.

The 

VM2145SS

 has a negative and positive

polarity. It can be used as sync output by setting its
jumpers to the appropriate position.

The 

VM2146UX

 is 8-output Universal Card that can

process video and sync output signals. See jumper
settings for sync and video output for more
information.

All input and output cards are “hot-swappable” with
finger adjustable lock-down screws and secure,
positive engagement card-edge connections.

TECHNICAL SPECIFICATIONS 

3

FEATURES/

DESCRIPTION

VM2144VS/VM2145SS/

VM2146UX

Output

Impedance

75 Ohms, 1%

Return Loss

40dB @ 10MHz

DC on Outputs

+/-30mV (max)

Equalization

+3dB @ 80-100 MHz

Gain

Gain

1.01

Gain Stability

0.01%

Gain Adjust Range

None

Gain Difference between
All Channels

2% max

Linear Distortions

Frequency Response

0-100MHz

Vertical Tilt

<0.01%

Horizontal Tilt

<0.01%

Low Frequency

<0.01%

Crosstalk

Video to Video

<45dB@ 5MHz, <35dB

@ 10MHz <31dB @

35MHz, <29db @

100MHz all inputs &

outputs hostile

Switching Characteristics

Switching Time

<10ms all channels

Video Input/Output Card Bandwidth (128x128)

Input 1 to Output 128

>280 MHz @ -3dB

Input 64 to Output 64

>280 MHz @ -3dB

Input 128 to Output 1

> 280 MHz @ -3dB

Output Sync Signal

Composite, Horizontal,
Vertical

TTL (+/-)

Impedance

22 Ohms

Frequency Compatibility

Horizontal

15-130kHz

Vertical

25-180Hz

Table 1. 

VM2144VS/VM2145SS/VM2146UX

Summary of Contents for 8-out Video/Sync Output Cards VM2144VS














Reviews: